Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I am trying to use a Raspberry Pi B+ as Bluetooth to Wifi bridge. But I find that the bluetooth range is very diminished when talking to my Nordic nRF51 and nRF52 devices...
Sir,
I have a question about the connection's power setting of the BLE.
I use the API as the screenshot, but there have a error return. I don't konw the reason, so I...
I am following Getting Started Assistant on Mac platform.
However, I run into an error when I issue: " pip3 install --user -r zephyr/scripts/requirements.txt ".
" ERROR...
Hello,
there’s a section in the NRF9160 specification (11.1) that calls out that VDD_GPIO should be applied after VDD has been applied on power up and VDD_GPIO should be...
Hi,
I am sending firmware image using my DFU master. The image needs to be divided into data objects each of 4096 bytes and then those again into 244 byte BLE packets. So...
Hello,
I'm trying to connect to nrf connect with the nrf9160 DK. I am using an Irish vodafone NB-IOT sim to establish the connection. This sim has an access control list...
Hi,
I have a question regarding a DFU update via BLE. I am using mesh sdk v3.20 and sdk v15.30 with custom hardware (nrf52840).
I have the BLE DFU working as expected...
Hi all,
I am using mesh sdk3.20 and sdk15.30.
I noticed that with the buttonless ble dfu, it is not possible to perform a DFU transfer after the device was provisioned...
I did the program using examples of glucose. But I do not want to enter passkey from central. Because there is no LCD or UART in my device. Which part of the glucose example...
I am developing firmware for my Peripheral Device (nRF52840) using S140 (v7) and SDK 15.3. In my application, I will advertise (with advert payload changes) and support Smartphone...
Hi,
How much is the expected time period from the time VDD goes above 1.75V to main()? I am using a custom bootloader and am seeing a ~4.5s (yes seconds!) delay in getting...
i'm trying to configure the nrf to rx and according to the state diagram i realized that: as the nrf is supplied and the voltage goes over 1,9V the nrf goes in the power down...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
I am trying to use the LPCOMP API, but I am having trouble with the following function:
nrfx_err_t nrfx_lpcomp_init
(
nrfx_lpcomp_config_t const *
p_config ...
