Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Trying to have the Nordic Thingy advertise to the ESP32. Using example code found in the ESP32 BLE Arduino.
When running the program, BLE Client, we are able to see and...
hi all,
how to revert interface MCU ATSAM3U2CA-AU(J-link )
when i plug in usb port to PC, DK board can't active .(PC can't detecting any USB Emulators)
check list...
Hello, I am using nrfgo studio to flash softdevice, application and bootloader on nrf52832 I am getting below issue:
" This hex file has data in SoftDevice region. Try programming...
We are using v0.4.0 lte_ble_gateway example running on an nRF9160-DK (0.8.5)
We are successfully pushing data from the UART on the nRF52840 to the nRF9160
Also managed...
Hello, I'll buy ISP 4520 (based on nRF52832) kit.
I request information about the processor's 'power down' of the LORA / BLE combo module.
Depending on the wake-up method...
I am currently working on adding the ambient light sensor to the asset_tracker application firmware. I have managed to configure the I2C, configure the sensor and read the...
I am developing an application as a peripheral based on the NRF52 SoC which regularly reads a sensor and publishes the reading to a BLE characteristic. A central (a smartphone...
I'm building some of the samples using command line in Ubuntu and have a strange issue. Everything builds fine, the merged.hex file is generated, however when I try to flash...
Hello All,
Currently i am working on nrf51422 DK board(PCA10028). I am using SDK 12.3.0 ,from this i have referred the ble_app_uart example for implementing the UART and...
Hello,
After following the steps of the tutorial : https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/getting-started-with...
I have an application that works on nrf52832 that when it is powered on is expected to read a sensor data for initial 10 seconds if any, and then start BLE advertising for...
Hello Nordic Team,
I have an application where i am playing some samples over i2s to an audio amplifier. The application also uses fds to store those samples (they can be...
Hi Sir,
In the latest datasheet (52832_v1.4), our reference schematic shows the cap (C6) of DEC2 can be NC.
For DEC2, it is 1.3V regulator supply for Radio, may I know...
