Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello, I'm trying to get an ANT+ peripheral example to work on an Adafruit nRF52832 breakout module. I'm using the 15.0 SDK, SD S212 and SES with a J-Link to program over...
Hi,all,
Now I am using nRF52832 to develop a Tire Pressure Monitoring System ,but I serached the ANT website and found that " a TPMS profile is "in the works". ANT+ members...
hi
i need to test the BT OTA test ( total radiated power (TRP), total isotropic sensitivity (TIS)
https://www.mwrf.com/test-measurement/ble-antenna-testing-helps-optimize...
Hello, maybe my answer didn´t get to you correctly. Referring to my post 10 days ago, I am still stuck controlling the joining procedure .
https://devzone.nordicsemi.com...
HELLO
I would like to know how to test RF for nrf24l0.
Of course, the RF test I'm talking about is frequency modulation for KC certificate
Previously, nrf24le1 was...
Hi,
Just to be clear, you are looking for reference DFU controller firmware for the Host MCU, in order to upgrade the firmware on the nRF52832。
I also need this feature...
Hello Developers,
I have configured a mesh network where I have a gateway node and multiple relays to relay messages from End nodes (sensors)
My question is the following...
Hi. I am working with nrf52832 trying to get Bluetooth and UART and a I2C peripheral working at the same time. I had a working version of the I2C peripheral and UART working...
hi.......
i need to run the program continuously using timer ......and want to check the data every one minute how to do that
i have seen timer example .. i am confused...
I am using nRF 5 SDK v 14.2.0.
I'd like to change the tone of the buzzer, how can I do it?
I'd like to make the following three settings.
Treble (+ 1 kHz), normal (+0...
HW: nrf52840
SW: nRF5_SDK_15.2.0_9412b96
source code: blinky_rtc_freertos example
Q1:
I read freeRTOS xtaskcreate operation on the web, it seem that I just need to...
Hi,
I am using Segger IDE.
I encounter error undefined reference to `nrf_drv_rng_init' .
I have include the below header file;
#include "nrf_drv_rng.h"
I already...
Happened when I occasionally compare the NRF_TWIM_Type struct in nrf52.h with the TWI registers (table 127) in nRF52832 Product Specification v1.4, there are many differences...
Will there be an HTML version of the nrf52832 spec document?
I hope Nordic is not expecting me to manually browse through a 550 page pdf document. I regularly use the infocenter...