Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
I have a problem getting fstorage to work with BLE in SDK 14.2.0.
The fstorage example works fine until i change
NRF_SDH_BLE_PERIPHERAL_LINK_COUNT to more than 0
In...
Im am running a nrf528322 board with the s332 softdevice using sdk14.2.
I have implemented flash storage in my program according to the nordic flash_fds example. This works...
Hi Nordic,
I am using SDK 12.3.0 and S130 2.0.1. I have some questions about AFH.
1. Do Nordic stack keep track of some bad channels during communication and would skip...
Hi I am working on pcb design for a long range application with nRF52832. There are lc circuit which is implemented to antenna pins on reference design of nrf52832. I decided...
Hello,
I am trying to develop a custom BLE service. I have been following this tutorial .
I have also looked at this answer to understand the signal path for a WRITE event...
Hi!
I'm using SDK13 (Softdevice version 4.0.2) and I noticed that during an update via DFU bootloader the update of the Softdevice doesn't work.
After the transmission...
Hi Everyone
I have been trying to use nrf52840 on a custom PCB . So far everything is working perfectly except only one single issue which is the controller gets reset and...
I'm new to the NRF series, and for that matter Keil. I have a BT832A which is apparently an NRF52810.
I am able to flash my own code using Keil and and control GPIOs to...
Hello, I am battling with weird problem for 2 days already, need little help if possible, I have tried all remedies and nothing worked so far.
Here is what happened, I followed...
Hello,
I am using SDK5 for my code that builds successfully under Linux, but not under windows.
The error occurs in the SDK, not in the application. I am wondering what...
Hi,
We are trying to optimize the speed at which we send data over BLE UART with the nrf52832. Currently, we are using the ble_nus_data_send() function in a while loop with...
Hi, I am a beginner at this and I want to make a scroll wheel that connect to Android devices as an HID device. I have a custom BLE board from Skylabs (SKB569) with NRF52832...
I'm having trouble using the NRFX SPIM driver on the NRF52810 w/ Softdevice (S112). (SDK15.0.0)
I'm able to initialize but when I go to use nrfx_spim_xfer without the callback...
I'm trying to change the advertising interval for a non connectable BLE device, but this does not seem to vary regardless of the value set.
The code I used is:
#define...