Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi, do you have a central peripheral combo example which illustrates indication (not notification)?
Alternatively, if you could list the steps to change from notification...
It seems GPIOTE interrupt do not trigger when multiple IN signals are defined as GPIOTE_CONFIG_IN_SENSE_XXX(false).
It works when GPIOTE_CONFIG_IN_SENSE_XXX(true)
I am...
With SDK 14:
If I flash in this order:
softdevice_s132.hex
bootloader_secure_ble_debug_ with bonds_s132.hex
3. ble_app_buttonless_dfu with _bonds_s132_with_setting_page...
I am having issues to use 2nd UART. When I run Keil in debug mode it shows me three UART registers.
i) UART0
ii) UARTE0
iii) UARTE1
Is this UART0 and UARTE0 same thing...
I am using NRF51822 Rev3 and softdevice 7 in my project. On communication with
Android device sometimes the link disconnects with disconnection reason61(0x3D)
BLE_HCI_CONN_TERMINATED_DUE_TO_MIC_FAILURE...
I have used nrf24l01+(production year=2015) in my project and my board and my program are working well......but when I change nrf24l01+(production year=2016) my board doesn...
I have an application where knowledge of the current date/time is important. This is implemented by the central passing the time to the peripheral when it initially connects...
I am able to flash/program nrf51822 with openOCD on Raspberry-pi and STLink-v2
but when I invoke Open On-Chip Debugger on telnet to write on UICR register, it don't give...
Hi everyone,
I am currently working on a project that leads me to save a respectful amount of data.
Some of the objects that I save size a few KB actually.
I would...
Estimate battery life for FOB CR 2032 -240 mAh
We are developing remote with CR2032 battery and using Nordic nrf51-1822 BLE, 960 m sec connection interval, RX 1 packet...
I want to use nRF52840 Device to implement non-connectable advertisement and scan on one board.
To be more specific, I want to advertise information for some time period...
I am using NRF52 SDK14.0 and SoftDevice S132 v5.0.0. Application freezes somewhere in SoftDevice if sd_softdevice_enable() is called after nrf_drv_clock_lfclk_request() was...
Hello All,
Where would I find a library file for a PID controller? Forgive me if there is an obvious answer. I'm new to working with Keil.
Thanks for taking the time...
We need to put the processor in sleep mode (to conserve battery power) and wake-up the processor when the user touches the Cap Sensor pad.
Can you Cap Sensor in nrf52 be...
