I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
According to developer.nordicsemi.com/.../ the IoT SDK was last time updated 11 months ago, which looks like a long time... therefore the question: Is IoT SDK still supported...
I would like to implement the mbed uVisor on the NRF52832 SoC with the softdevice s132.
So I created the configuration files and wrote some code.
Now I have problems with...
Hi,
I am trying to compile some RuuviTag application using nRF5_SDK_12.3.0_d7731ad
2 symbols are not defined,
APP_CONFIG_ADV_FRAME_SPACING_MS_MIN and
_ADV_FRAME_ETLM_SPACING_MS...
Hi nordic guys,
After the hid device delete the bond info but the PC did not remove it form the bond list,and i want the hid device to reconnect the PC quickly again but...
Hi,
in nrf connect app i see it is possible to update bootloader over ota.
How do i generate ota file properly? I tried generating zip and hex but the app says "no matching...
I have nRF6310, nRF2727.
I wonder if I can update the nRF24L01 firmware with the above board.
I wonder if there are any additional devices or other methods...
I am using ble_app_uart in one nRF52 EVK board(peripheral) and ble_app_uart_c in another nRF52 EVK(central) and sending data of Device under test through UART. When the data...
Hi,I want to use RTT in bootloader project.
First,i add all files(SEGGER_RTT.c ,SEGGER_RTT_printf.c,RTT_Syscalls_KEIL.c) to my bootloader project(Picture 1).
Second,I add...
hai
in nrf51822 the pins p0.01 t0 p0.06 are marked as analog pins in the nrf51822 DK.
i know that in arduino we can use an analog pin as an analog input as well as a digital...
Hello!
I am developing with mbed. According to nRFgo Studio, the hex file generated by the mbed compiler already contains the following SoftDevice: S132_nRF52_2.0.0 (Id...
Hi all, I'm working on sdk11.0.0 and s130 softdevice. In my project I want to send data coming from uart to ble and data coming from ble to uart same as ble_app_uart example...
Hi there,
I am working on programming the CTS ble service on my code.
In order to do that I also have to include db discovery.
#include "ble_cts_c.h"
#include "ble_db_discovery...
Hi,When I use nRF Connect app(IOS version) to connect my ble device,BLE_GATTS_EVT_SYS_ATTR_MISSING log information appears in my RTT Viewer(Picture IOS_Phone_Conncet).After...
Hello,
I tried as you mentioned using sdk12.1.0 buttonless_dfu and bootloader_secure example.
I didn’t modify anything except dfu_public_key.c.
As shown in the attached...
Hello,
I have a program that do an infinite loop in sd_softdevice_enable. How can i investigate ?
Loop is from 0x00009DEA to 0x00009DF2
Target is nRF52832 AA with...
