before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
I am using a custom nrf51822 board and S130.
I am trying to pull data from a sensor over SPI and then immediately send that data over SPIS to another processor. Is this...
While trying to implement a simple qdec demo application, I find that QDEC_SAMPLEPER_SAMPLEPER_512us above works ok, yet QDEC_SAMPLEPER_SAMPLEPER_256us does not work at all...
I have a case where I'm using a timer/counter as a counter with one PPI channel routing a GPIO rising edge to the COUNT task. Another GPIO rising event controls the counting...
I have an nRF52 paired to a central device. In order to delete the pairing on the nRF52 I clear the persistent data (dm_init_param_t).
I notice, however, that even though...
Hi all,
I'm a grad student trying to innovate on the BLE concept. I require a continuous signal as a source: preferably unmodulated, but a long duty cycle could also work...
The NRF52 product specification (aka, datasheet) has 3 chapters in it all relating to TWI: TWI (chapter 49), TWIM (chapter 33), and TWIS (chapter 34).
Which section (TWI...
Hi,
I'm trying to interface SIM808 with nrf51822 over uart using nrf_drv_uart. Everything works well for some time, but then uart starts reporting error code 1, NRF_UART_ERROR_PARITY_MASK...
Hello,
I am working with the GPIOTE library to get a GPIOTE_IRQ from a peripheral.
I have several questions regarding the library and how IRQ works.
1.How do I clear...
Hello,
I am using SDK7.1.0 for NRF51822.
In my subroutine, I would like to disconnect with the peer device, and re-advertise. But when after re-advertising, I found the...
Is it possible to set scope for search in info-center only for SDK 11? It search in all SDK versions and sorts results randomly. It is very annoying. Especially when there...
Hi,
I want to build expertise in BLE and want to use the Nordic nRF51x22 to build a hardware and write the firmware for the same.
I am planning to use the nRF51 DK....
I'm calling sd_ble_gatts_characteristic_add multiple times to add characteristics to a peripheral. At some point I get a return value of 0x200020B6. I'm not making much headway...
Hello everyone,
I am trying to use the ble_app_hrs_rscs_relay example from SDK V11 for s130 (2.0.1).
It compiles and works well when I use an pc10028 evaluation board...
If I have multiple services, 2 for example, how should I set up the srdata.uuids_complete.p_uuids in the code:
ble_advdata_t srdata;
memset(&srdata, 0, sizeof(srdata)...
Hello,
I am developing beacon on nRF51DK and I want to store in non volatile memory some parameteres like:
ProximityUUID
Minor
Majnor
AdvInterval
Tx_power...
