I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello.
I have downloaded and installed Nordic STK and nfrfprogtools.
Now i am trying to through devzone.nordicsemi.com/.../ tutorial.
I successfully loaded s130 softdevice...
Hi,
Is there any method that I can use to get the LE Packet or the Baseband packet ( With Access Address) passed onto the application? (Using S110 or S130)
Thanks
I started by compiling BLT uart app successfully on MDK5 but found out that it is giving errors on the startup files in the Device Pack.
I tried to refresh and update Device...
Hello Everyone,
I am trying to measure the (3v)battery voltage by having proximity example as reference but intially it is showing 100percent later it is going to 13(percent...
Hi,
SDK: v11.0.0.2-alpha
DK: PCA10040 (NRF52)
I am trying to build a peripheral application that communicates with an external device via UART (h/w flow disabled)....
Hello!
I have PCA10006 with revision QFAA nRF51422
I am testing the buck converter's ability to make the system consume less power when transmitting.
Example is ant...
hello there! i am working on project in which my one nordic BLE(A) want to send command to second nordic BLE(C) which is not in my range. now there is third nordic BLE(B)...
Hello Guys,
I would like to know, can i use NRF52 Preview DK on Board Segger Section as standalone Segger JLink Programmer for NRF51?
So, is there any way to dis connect...
Hi, I read about concurent operation of the Softdevice and other proprietary stacks like esb or gazelle using timeslot api. Is it possible to run two ble stacks in this way...
Hi Guys,
I would like to develope a HID device on nRF52832 chip. I'm woring with nRF52 Development Kit (PCA10040, v0.9.0).
I've tried to flash the board with both hid...
I'm getting the NRF_ERROR_NO_MEM when I try to put my ADC interrupt routine into the scheduler. The code runs without error if I run from the ADC interrupt handler directly...
Hello ,
I am testing the DFU support and usage for the next phase of my project. I am using S110 softdevice 8.0 and SDK 9.0 and evaluation kit nRF51822QFAAG0.
I followed...
hello, I have some quesetion about the nrf51822's carrier detect. I want to use " CSMA" to avoid
Communication collision, the datasheet has no detailed infomation about...
when I call pstorage_store so store a block of data, sometimes I call just after pstorage_store : the following code
do {
pstorage_access_status_get(&count);
} while...
In this post , I can register a new case with some required parameters to have the current estimation, but I don' t know how to obtain some of them.
I'm using nRF51422...
