I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_CONNECTION_TIMEOUT?
please someone give...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_LOCAL_HOST_TERMINATED_CONNECTION?
please...
Hi all,
I am choosing a oscillator and my choice was a 16MHz stability +-9ppm, tolerance +-10ppm, 9pF
my FAE gave me the hint to use a 32MHz which is stability +-20ppm,...
Hi,
I have my BLE services arranged in different .c files. If I change anything in these files and compile (using Keil uVision 5) and load the program, it seems like the...
What is the designed (/actual/required due to the specification) behaviour of the Bluetooth stack S110 when notification packets are queued and the CCCD controlling the attribute...
I am looking into using Internal RC instead of External Oscillator (with softdevice on).
The function ser_app_hal_hw_init() uses Xtal clock source by default.
...
Hi, everyone. What is the meaning of datasheet "section 8.5.7 Antenna matching network requirements"->15+j85 ?
Whether is that we can caluate the 50o with the data?
bonjour , j'ai essayé de communiquer deux pca10028 en utilisant l'exemples " transmitter_pca10028 et receive_pca10028 " mais l'experience a echoué je sais pas pourquoi sachant...
Hello,
I'm testing current time service client example on SDK 8.0.0 with iOS.
After connected the devices, iOS show confirmation to pairing.
When I canceled this or...
After enabling and starting the watchdog timer (RR0), how can it be disabled?
This following code does not work :
NRF_WDT->RREN &= ~(1 << WDT_RREN_RR0_Pos);
Neither...
Hi,
I use s120 stack and ble_app_multilink_central
I use function sd_ble_gattc_primary_services_discover(p_client->conn_handle, start_handle, NULL) for discover services...
The sniffer software doesn't seem to find the device on either of two different PCs here, and I'm not sure what we could be doing wrong.
The installation steps were the...
Hello,
I have recently got a n5 start kit nRF51422. I went through all the set up procedures in the user guide, installed all the correct programs/drivers etc.. My unit...
Hello.
I am looking at the schematic of the nRF51422 USB dongle development kit. The pin P0.30 of the microcontroller is attached to ground. As the pin could potentially...
