I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hi，I would like to know how it works when reconnecting after a timeout disconnection，I didn‘t find the answer after reading Bluetooth 5.4 specification.
Hello,
I'd like to download the latest MDK for SES - links here appear to go nowhere: https://www.nordicsemi.com/Products/Development-tools/nRF-MDK/Get-Started?lang=en ...
Our design has an nRF5340 with a 32 MHz high frequency crystal and an accurate 32 kHz external rail to rail clock chip (+/- 5 ppm @ 25 C). We would like to measure the actual...
Greetings,
I am facing a problem making my BLE device change its advertising name by parameter received from UART. The advertising name is generated using my function...
Hi,Team,
I am developing ble using nrf54l15-dk.
My goal is to get the ble identity address of the device, but I don't know how to read it.
I found " bt_addr_le_create_static...
Hi,
I'm integrating a VCNL4010 over an I2C connection via an nRF52 DK.
Noting there is a Vishay VCNL4040 sensor driver, has anyone written one for the VCNL4010? It...
Hello Team,
I am currently experiencing difficulties connecting my nRF7002DK to AWS IoT Core using the aws_iot sample in nRF connect SDK v2.9.0 , which I have adapted with...
Hello everyone,
I have a custom board with an nRF5340, which currently uses the internal clock. Im using toolchain v2.9.0 and SDK 2.9.0.
I'm trying to use the RV8263-C8...
I have tried building the nrf example projects and they build fine. But this project gives this error.
The version I am using is SEGGER Embedded Studio for ARM Release 7...
here is 2 question for this example. (v2.9.0) as i looking for this example, there are some limitations like belows.
One BIG, one of the two BIS streams (selectable...
Hi
I remember the Devzonw could ask for hardware instructions. My matching circuir has used the nRF54L15 reference design and nRF21540 DK design, all the value is the same...
I am developing a proof of concept project using Wave share BLE400 module and the final product of this project should work on button battery backup for years. so essentially...
Hi, I recently upgraded our ncs SDK version from 2.6.0 to 2.9.0 for a custom matter application development using an nRF5340. We also support a smaller debug app that is BLE...
When setting the following channel sounding parameters with bt_le_cs_set_procedure_parameters I am getting E: Failed to set procedure parameters (err -22) or BT_HCI_ERR_INVALID_PARAM...
