Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Excuse me:
The SPIS example in SDK is shown in the figure below,the m_rx_buf buffer has only seven bytes，Does NRF_DRV_SPIS_XFER_DONE event occur when the buffer is full...
I am developing a NRF52810 product, I am downloading using JTAK on NRF52832 development board.
I have the NRF52810 because of the lack of IO pins. SPI CLK , TWI CLK are...
I use the NRF Mesh SDK v2.2.0
- EVB PCA10040 burn the serial example
- EVB PCA10056 burn the light server example
- PCA10040 attach to the Raspberry Pi 3 via USB for...
I'm trying to follow these instructions to update the openthread binaries in nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8.
I have a Windows host machine and a Ubuntu VM...
Hi,
I am trying to do AGPS with the supl library. I obtained version 0.7 through the application and installed it (and enabled the required config options).
Unfortunately...
Hi Nordic,
I am working on project with nrf52840 , which is a central to connect other device. we will enter the MAC address to central, and setup the scaning filter.
...
Hi all,
I am trying to do bonded buttonless DFU but an error named NRF_ERROR_FORBIDDEN was raised in enter_bootloader() function under ble_dfu_bonded.c.
The description...
hi，
I currently have an application scenario，using a nRF52832(M board) BLE maser to upgrade another nRF52832(S board) is run standard DFU ，Are there any demo available？
Previously, I used SEGGER to build and run programs on nRF52 DK very quickly (5-20 seconds).
However, for nRF5340 DK, it usually takes about 8-15 min to build and run just...
Hi,
I am trying to connect the current product with MCU EFM32GG290F1024 to a Nordic BLE module in a serialization over UART.
I have port the SDK to my project and need...
1. hardware : nRf52840 dongle.
2. Purpose : Update Firmware into dongle to be sniffer, and restore original default manufacturer firmware for nRF Connect v2.6.0 desktop...
Hello All,
i my project there are 2 ble services now i want to add Flash read/write application i tried with fds as well as flash_write example from the SDK 15.3.0
i added...
Hello!
Apologies in advance for my english.
I already asked a similar question, here is the link to it
When trying to connect a PWM driver PCA9685, I ran into problems...
