I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I faced several troubles when I worked with Bluetooth: Mesh sensor client and Bluetooth: Mesh sensor server examples. Firstly, I couldn't build the application "Bluetooth...
Hi, i want to flash my modified code in my customized boards , which hex file should i use for flashing the customized nrf52832 board usinf nRF CONNECT . I need a hex file...
Environment:
DSL-Router, IPv4 only, DHCPv6 disabled
Raspberry PI 3B, RaspPi_OT_Border_Router_Demo_v4.1.0-1.alpha.img, the raspberry is connected via wire with the dsl...
Hello,
I've been running some power measurements on our prototype board that is using the nRF9160. I've measured current draw on the VDD and the VDD_GPIO when the modem...
Hello ,
I am currently working on NRf52810 , SDK version 16 , I want to send around 400 bytes of data over BLE connection from peripheral to central. I know that NRF52810...
Hello, I am working for a BLE central application where the packets are send using L2CAP Connection-Oriented Channels. My development environment is based on nRF52 development...
I'm trying to get the ble_app_blinky example from the NRF5 Thread SDK working on the Adafruit Feather nRF52840 Sense using the S140 soft device v. 7.0.1 I'm compiling the...
I have a custom board with the NRF52832 chip. The supply is from a Lipo battery which after 3.6v varies from 3.6v to 2.5v. hence I have a varying input supply to NRF. Would...
Hi,
I am using TWI on a 52832 (sdk12.2) and am having problems with reading data. The slave chip that can take up to 60uS (8 bus clock cycles) between to set up data after...
Can the Nrf Mesh android app be expanded to support multiple networks?, i took a look at the android software , it uses MVVM architecture and uses Dao's and repositories to...
Hi,
I found that s113 SDK17,did not support +8dB TX power,could you please give me some suggestions ,when using nRF52820, which SoftDevice will support +8dB Tx power?Thanks...
Good afternoon,
We are carrying out a new project with your NRF52810 beacon to create a heat map of
movement inside a room.
Our questionis, do you have any software...
Hello,
I am currently running the openthread client example provided in the NCS and I am trying to toggle the client as a sleepy end device. However, in the toggle_minimal_sleepy_end_device...
Hi
I would like to know the availability of the open sources for the following:
1. BLE Gateway for PC, Android , iOS
2. nRF Cloud open source
Can you help, How to...
