Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
I just tested with the example project, "ble_app_uart" using SDK, "nRF5SDK17009d13099.zip" on nRF52DK (labelled with PCA10040 1.2.4 2018.23) board on Segger embedded studio...
Hi ,
i am trying to interface a WINBOND W25Q64JV flash module with NRF52,i can able to read device id,status register success fully.
i wrote the data in particular address...
Hi,
I'm using nRF52840 DK as a central. Our project is based on ble_app_uart_c example. There is filter for UUID only during scan.
I noticed, that for conection establishing...
I'm using the nrfjprog command "nrfjprog -f nrf52 --reset". This sometimes causes my custom board to hang. I dont think it is able to boot at all, I do not see any uart output...
I would like to ask Nordic to create an example of an Android background service that can detect a device advertising.
Android imposes background execution limits which...
I am using nRF52840, SDK 16 + s140 with segger embedded studio.
I have already added NUS service to my application by taking reference to ble_app_uart example. I want to...
I need to somehow connect 10 i2c devices to nrf52, to do that I need 5 i2c peripherals, but nrf52 has only 2.
I see different options:
1) Use multiplexer. Probably a good...
Hello, support team.
I try to use nRF Connect v3.4.2 on Ubuntu 16.04.6, VMware.
But there is no response after executing specific application eg. Bluetooth low energy...
Hello everyone,
I have problem with a code for reading BME680. Here is my code the values display are wrong and never change.
Thank you for your time. I used this Library...
When adding the DK to my nRF cloud account, I get the following error message: " There was an error adding your device: nRFCode 40102: Ownership code [HWID] is invalid for...
nRF52840, SDK v16.0.0 SD140v7.0.1
Our electrical engineers gave us a hard ATT_MTU limit of 65 bytes, so as to keep the peak current low on the battery for our ultra-low...
Hi,
I'm running into a problem where a TWIM TX call gets stuck internally waiting on the NRF_TWIM_EVENT_STOPPED event. It never breaks out of this while loop in the twim_xfer...
Hello,
I'm trying to integrate the nrf Calendar example here with Current Time Service client implementation on a nRF52840 DK.
I'm trying to understand the logic of the...
Hi, i am new to the nRF52832, Now I want to use it in development.
I need to use it to send Running Dynamics data.
I would like to ask everyone, is there a related demo...
