Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
We need to install nRF Connect SDK v1.2.0 on a new machine. I followed the provided steps, using the Toolchain Manager (previous "Getting Started" method is deprecated, apparently...
Hi everyone,
I was looking at the SAADC example and I need to modify it in order to fit my design. I want to perform analog readings from eight sensors using an eight-channel...
Hi,
I'm developing a BLE application that is also using FreeRTOS.
I also need to use PWM to control an LED (mainly because the requirements define LED patterns, which...
Base BLE structure ble_advertising_t contains a member structure ble_adv_mode_config_t. This structure contains two parameters that are meant to limit number of advertisements...
Hi Team,
I want to create on flash section to store the specific data like Crypto Keys and Serial numbers. How to create one page/section in existing Flash memory without...
I am trying to test a BME280 sensor on the nRF9160. I followed the steps where I created a folder (board) and added the nrf9160_pca10090.overlay and add couple of line in...
Hi, I would like to implement free rtos on nrf 51 using IDE Segger Embedded Studios. Could some one please direct me to the necessary links/ information.
I have researched...
Hi ,
I am working on project which is based on nrf9160 Development board.
could you please verify these points-
1. I am sharing the snapshot of the registers...
I have downloaded the Keil compiler and the Nordic key for same.
When running Keil_v5/UV4/PackInstaller.exe I can not get the update:
Cannot download file developer.nordicsemi...
Good Day,
i´m want to use saadc with 7 channels. I´m using the ADC Driver with an interupt handler. All 10ms the sampling starts per cpu. I use the configuration followed...
Hello,
I am running on a NRF52840 DK a Zigbee program configured as a router. For the coordinator i am using the cli example from the SDK.
On the router, I have developed...
Dear Nordic Semi, ladies and gentlemen!
I'm working on a prototype device with USB host functionality. I am using Arduino USB Host Shield connected to nRF52840 DK . DK is...
Hi，
We want to confirm the effect of GPS fix_interval and fix_retry, so we start GPS with parameter fix_interval=10s, and fix_retry=30s, then get the result as the following...
I try to bonding.
Using SDK 15.3. 0 and S332 Softdevice.
I successed bonding procedure used Peer manager.
after bonding, If I try to connect one more, nRF Connect app...
