I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello.
I just import Thingy firmware: thingy52_ses.zip and try to build this project and check possibility of programming my Thingy, but SEGGER returns something like that...
When I use nRF52840 dongle as a promiscuous packet sniffer , I found that sniffer works fine no matter how much I set the baud rate. This happens only on the dongle, so I...
Hello,
I have a PWM code that works as a peripheral application on my nRF52 DK, but now I want to set it to be controlled via android phone app. I have nrf connect on my...
Hello,
I'm a newbie to BLE and the Keil uvision IDE. I'm using a nrf51422_xxac_s110 chip, The version of the IDE I'm using is 5.28.0.0. When I add the fds.c file, into the...
Security of data passing in BLE communication Hello I am developing based on "multirole lesc" of BLE sample project. What is worrisome about the project is the "security_req_t...
I don't program the BLE part myself but I must know from a design-level.
As I understand, a BLE scanning unit must connect within less then 60us after advertisement.
If...
Hello.
In according to this tutoraial: https://www.novelbits.io/bluetooth-mesh-tutorial-part-5/
I wonder if it is possible to replace ,one of these two nrf52840 DKs...
Hi,
Has anyone had success going from the Arduino bootloader back to J - link bootloader?
CONTEXT: I purchased 5 nrf52832 modules, and followed the posted guide to burn...
Hi, I would like to power my development board from the provided coin cell. I removed the plastic between battery and negative contact point. I put VDD position on power source...
Hello. Can you tell me which project can I use as a template from nrf 5 SDK with basic RX/TX data send/receive payloads API? Want to build custom simple-structure mesh, with...
I want to use some functionalities of Zephry OS. Example https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.0.0/zephyr/samples/gui/lvgl/README.html .
I also want to...
I am rebuilding my computer after experiencing a corrupt boot sector and am reinstalling all my apps. I am moving from Kiel 4 to Kiel 5. My project loads, but it says that...
Our manufacturing supplier provided me a log file from the nrf Connect for Desktop Application that shows repeatedly unexpected disconnects when nrf Connect opens a second...
Hi,
Do you have a sample ANT radar profile example with all the pages defined, similar to ant_hrm.h in SDK 15.3 components/ant/ant_profiles/ant_hrm/pages/?
Thanks,
Abid...
Hi Admin,
I just bought development board Thingy 52 from Digikey. I coudn't find design files that consist of hardware design in Nordic website. Could you advise for this...
