Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hi Since we're almost done with the programming for our application we would like to move from the Development Kit to a custom board as similar as possible to the final PCB...
I am using the legacy bootloader, SDK 11.0 with SD 2.0, S132
The example Bootloader DFU images part of SDK 11.0 load just fine (I'm using nRF Connect Android app), however...
Hi, I've been recently working on trying to stablish an i2c (twi) communication between my nrf52 Dev kit and a LIS3DH located in a STEVAL-IDI-003V2 board.
In this post https...
Hi!
I have used NRF52832 on PCA10040.
I want use several pair (master and slave) in one room.
For this I try to select a different frequency for each pair.
But, when I...
When trying to use BPA600 BLE analyzer I was not able to see the LL packets. when contacted Frontline/Teledyne tech support they said I am into BLE 5.0 stack.
However so...
Hi ,
I configured nordic as slave and it looks like the transactions been successful, but when 2 SPI transactions occurs consecutively slave was setting 0xAA in return...
Hello, we are developing using nRF52840 DK, SDK version 15.2 and Mesh SDK version 3.1.0, using Segger Embedded Studio.
Currently we are using the nRF Mesh app to provision...
Dear support team,
I wanted to program and debug nrf52840 dongle through an external debugger. For that, I connected the debug out of nrf52840 development kit to the SWD...
Hi, I recently added the buttonless DFU bootloader on my device with the debug config. I am using and I can flash an application when in DFU. Although, I cannot debug my application...
Using the Mesh SDK 3.1.0 the advertising bearer's transmission interval is limited 20msec (B EARER_ADV_INT_MIN_MS).
The Mesh Profile Spec indicates in s4.2.19 that the transmission...
Is it possible to transfer 258 bytes over the TWI interface of the nRF52832 in one transaction ? The manual says that RXD.MAXCNT is 8 bit wide only. I need to read 258 bytes...
Hello,
I need help with my project. I am adding fds library to the light sw example.
I did this steps:
1. Included necessary *.h files
2. Added fds.c to the project...
Hi, I'm using nRF52840,
I created my app, then i tryed to program with bootloader using nrfutil.
I used dfu bootloader and i created a zip.
So i could flash bootloader...
Hi, every developers,
I am testing the example of ble_app_hrs_c and ble_app_hrs using 2 nRF52840 (in SDK 15.3.0 VERSION).
My goal is that data communication with two DK...
SDK : Mesh 2.1.1
IDE : SES
I have a node.
After this node provisioned the mesh network,I change this node model publish address by local.
then I restart this node...
