before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
I'm having trouble implementing the workaround that was mentioned in the following previous post: https://devzone.nordicsemi.com/question/55937/nrf52-sending-an-octet/
...
Hey guys,
i am trying to add new firmware to a cheap fitness tracker I have. After I write the new firmware in the Nordic SDK, I think I save it as a hex file. I’m not sure...
Hey Guys, I am trying to calculate goodput and delivery rate using nrf52840 pdk devices in ble mesh. Does anyone had already tried it before and shed some lights on starting...
Hi!
I am planning to port SPI sending and receiving functions to the sample code of ble_app_uart of SDK 14.0.0.
The transplant was finish, but when I am debugging, if...
https://www.nordicsemi.com/eng/Products/Getting-started-with-the-nRF52840-Development-Kit
Hellosupport,
Just got my 52840-DK board (v. 1.0.0), got the pulsing LEDs...
Hi everyone, I'm having an issue with the power draw of my application (SDK 15.0.0, SD 132 v6, Sparkfun nRF52832 Breakout). The application does roughly the following: it...
HI all,
I'm trying to use the ble_nfc_pairing_reference example from SDK 15.0.0
I installed microECC and can now build the example using GCC on Windows.
A first...
Hello,
So i recently bought a PCB with a nRF51822 microcontroller and accelerometer. The accelerometer that is on the PCB is the lis2dh. Now I want to program the nrf51822...
hi guys ! i'm looking for help with the creation of a ble service for a nrf52840 dev kit.
i tried following the tutorial https://devzone.nordicsemi.com/tutorials/b/bluetooth...
hi!,everyone:
i found if i open the watchdog in the code, it reset the system according to the register CRV, can i close it before it reset the system?
hi,
i am using nrf51422 with sdk13.3.0 and soft device 130
i want to send 69 bytes of data,which is the best way to increase packet size
By creating custom service,can...
Hello All,
I made 2 custom boards, both mount a n52840 QIAAC0 chip. I was able to program them using the "ble_app_uart peripheral" and "ble_app_uart_c" codes that I found...
Hi,
Board: nRF52840 PCA10056 Development kit
Keiluvision 5
SoftDevice : S140
nRF-SDK 15.2
SDK example code: ble_app_uart
Hi, I want to change the BLE range...
Hi,
nRF905 is still manufactured, right? I didnot see anything on Nordicsemi, but I've seen on Farnell's web page "No Longer Manufactured" and on digikey it was not available...
Hi!
I'm using nrf8001 to send twenty 20-byte packets to a phone application. The connection interval I use is 30ms. However, I takes 5 seconds to send the data to the phone...
