Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi, I want to advertise each 3times every 5seconds as sometimes beacon scanner can't read it so I need 3times in series advertising.
in main() I added 3times advertising...
Hi there, I am working on NRF52 DK, SDK15.2 with SD 6.1.0, The issue I am facing is that the DFU service is appearing on Android device and I can update apps using NRF toolkit...
I am trying to connect nrf52832 with custom android app, after connection established beacon sends message. Sometimes I can establish the connection after 8 tries, sometimes...
Hi,
I'm working on a project which uses two nRF51822 (SD130 and SDK v11.0) on mobile devices. Device A is continously advertising and device B scans for a fixed interval...
I'm looking to sync an ADC reading with the PWM output. I'm using PPI for this but fails to make it synchronise properly with the PWM.
I'm getting interrupts and sampled...
Hello,i am using nrfsdk with softdevice 6.0.0 in my application and by using it i am trying to connect my mobile uart application with my BLE .but i am facing some issues...
Hallo all
I have an appliation using the LOG for TX output to uart,
I want to maintain this code but to add RX based on the app_fifo_init,
how can they coexist ?
thanks...
Hi,
I would like to use the nrf52 as my bluetooth end device, which inturn has to communicate with the Bluetooth IOT gateway like Rigado module or Nordic gateway APP(which...
Hi
I am using SDK 14.0.0 and soft device S130.
I am planning to add SPI functionality to BLE's sample code.
However, when moving to the next instruction after SPI data...
I am developing a beacon using nrf52810. This beacon will advertise iBeacon as well as Eddystone packets. And user should be able to configure some of the beacon paramters...
Hi Nordic,
I am using the example nrf_app_interactive with nrf52 DK. I am using it as a central while connecting to a peripheral. This peripheral has a lot custom services...
Hi,
I need implement a single Byte transaction on SPIM.
I implemented a stop as documented in
setup_workaround_for_ftpan_58 function
It works only for the first...
I want to use the RTC Tick Event as my system tick. But on both the RTC0 and RTC1 my programm freezes after about 8min.
It looks like the Tick interrupt is still served...
Hi,
We are currently at the process of manufacturing prototype boards, the manufacture cannot do pitch size under 0.25mm. They kept telling us that the chip's BGAs exceed...