Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hello, I am having trouble with output display on my nrf52840dk.
I tried resetting the device. It has no effect. I using RIOT OS to flash the board. PyTerm outputs nothing...
Hello, I've been evaluating the PDM hardware driver for the nRF52832, and the PCM output of Thingy. I've found that, for certain impulses at the input of the microphone, the...
Hi I have successfully set up my ARM SPI interface to use the nRF24 chip. At this time I'm trying to establish connection but I'm not sure I under stand the setup for comm...
I'm getting this when im trying to select the device.
when i try to update the firmware nrfgo studio is getting closed
please help me in solving this!!
Let's first compare two pieces code:
This one works:
But this one doesn't:
My problem is that as soon as I try to process received data, some of data is lost. Is...
I am developing with SDK 15.0.0
I want to add NUS service in ble_app_buttonless_dfu example.
All I have done:
1. Add including files and including paths to the project...
This is really a two part question.
1. How do I even refer to pin P1.00? It's clear that pin P0.06 is referred to simply as pin 6, but what is the naming convention for...
Hi,
i try without succes to go into MemoryRentention Timer On sleep mode, and wakeup with the analog comparator activated by AIN1 without sucess. Here is my code, please...
Hello I am using nrf52832. I would like to write a custom ISR for GPIO based interrupt. Are there any examples/documentation i could use to get started on this.?
Dear All,
we use Reference configuration 4 and have connected the DK to our custom PCB. 3.3V of the DK go into VDDH and otherwise only GND and SWDIO/SWCLK are connected...
hi
i downloaded nordic thingy52 FW and i uploaded on my board PCA20020
and that is working correctly but when a i downloaded nRF5_SDK_15.0.0 at first i compile (ble_app_beacon...
Dear Nordic,
i am just testing ble examples in nrf 52840 dongle and also implementing one uart for just testing
TX pin - 1.10
RX pin - 1.13
transmission works fine...
Hi,
I'm referring to -
1. Custom HID over GATT device
2. nRF51422 HID example modification
So for now, I just used the descriptor mentioned in above links. But "hello...
Hello,
The softdevice S132_SDS_v4.1 spécification write that supports 20 connections at the same time.
I would like to know if it's possible to have 1 central and 20 peripherals...
I'm attempting to make cli application to load from after the softdevice and based on a command enable/disable the BLE functionality. Is there any simple way to do this? Are...
