I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi everyone,
I am currently trying to implement USB headset on nrf52840. As far as I can see the audio example from SDK14 uses SyncType=None meaning that bmAttributes bits...
I want to change type from "uint32_t val1 = 0xAA01" to "uint8_t val2 = {"AA01"}.
Then, attr_char_value.p_value = val2;
=> sd_ble_gatts_characteristic_add(p_rms->service_handle...
I am currently trying to develop Mesh applications using the Nordic Mesh SDK and the nRF52840 Dev kit. The problem that I am having is that my testing equipment isn't able...
We have a custom hardware device that uses the nRF51 and the S130 softdevices. We are able to connect our device to our app on iOS and Android and through a web-bluetooth...
I want to erase selected pages from the NRFflash memory (Not whole flash).
I have defined one function for NRF memory erase. In that, I have followed following sequence...
Hello, i am using NRF 52832 QFAA
In pstorage_platform.h I see
#define PSTORAGE_FLASH_PAGE_SIZE pstorage_flash_page_size()
and the return value of pstorage_flash_page_size...
Hi Nordic,
I have been quiet for a long time but here is another question.
For the project I am working on I want to measure the current with the PPK. Although it seems...
Hello. When I received nRF52DK, I have successfully uploaded some examples also with softdevice through the Keil IDE. But after few days Keil and also Segger IDE stopped detect...
Hi. I'm new to both the nRF24L01+ and to this forum.
I'm intrigued by the prospect of using these amazing little transceivers as RF modems. Because I find elements of the...
Hi,
On SDK12.2, I replaced main.c in ble_app_template with one in twi_scanner and modified sdk_config.h.
But, no expected log, even "TWI scanner.", issued to terminal...
Hi,
I want to add a service to the "ble_app_beacon example" that i can change
the value of the major and minor directly via nrf connect, some one can help me
to add the...
If I leave the CE pin in a HI state, and assuming I have the PWR_UP = 1 and have loaded the Tx FIFO with data, will the data be transmitted by merely setting PRIM_RX to a...
I've paired ble device with android and then device went out of range and wen ble device comes into range device will connect at that time do we get any callBack???
