I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
In the ULP Wireless Q magazine (edition winter 2016), on page 12 / 13 there is listed that the nRF52 chips have a Battery Monitor peripheral but I cannot find anything about...
I have been developing my application using gcc on an NRF52 by putting the text section at 0. This was convenient to get going quickly. We initially weren't going to launch...
hello, i am doing flash read and write in nrf51.for which i have used the C:\nRF5_SDK_12.2.0_f012efa\examples\peripheral\flashwrite\pca10028\blank\arm4 this exampl.
but while...
Hi,
Could somebody share the schematic and board files of nrf51 beacon?
We are planning to make some changes. I don't intend to buy a beacon because I have already purchased...
Hi,
I use the bootloader in the SDK V13.0, I found that no timeout as the SDK v12.x. However, I have added the WDT to the bootloader refer to the link link text
it still...
i could not run timer2 with soft device,. if i start initiaize TIMER2 the bluetooth advertise has disabled. i need this timer to timeout my flow function. i think softdevice...
Hi,
I used the hrs example found some problems, the problem is described as follows:
I use the Android phone pairing binding device, when I cancel the pairing on the phone...
hello,
What is the difference between the next two events?
On_ble_evt ()
BLE_GAP_EVT_TIMEOUT == 0x1 B
On_adv_evt ()
BLE_ADV_EVT_IDLE
I can not understand well.
With...
Hi;
I do not know the BLE Event(DFU bootLoader/SDK Sample) so I will ask you a question.
The environment using is below.
SDK v10.0.0 (Sample code/dfu_transport_ble...
I was trying to save this :
char a = 'r';
uint8_t save = a ;
record_chunk.p_data = &save;
Or even this :
char *point ;
char word[5]="lala";
point =word...
How to prgram nRF beacon kit as peripheral with KEIL and nRF DK52. I cannot see the beacon kit to be programmed. KEIL says DLL error.
Please let me know thw KEIL settings...
hello,
i am trying to compile libmbedcrypto.a but the Make file is pointing to a non existing file called /mbedtls/sha256_alt_cc310.c.
Any idea where i can find this file...
Hi,
I'm using the FDS library to store some data (configuration data). For production, I'd like to flash an initial configuration to the nRF52832. I know the storage format...
