before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
To my very limited knowledge, it has something to do with an "attribute table" of some sort. So you will have an init function, where you get to write all your attributes...
I use active scanning ，the observer will send a scan request when it hears and advertiser, and will listen for a scan response.I only see the scan event，but sent request and...
hello in nrf51 sdk, nordic has already ported freertos.
but if i want to port myself. can anyone tell me how to do it??
first i downloaded freertos from website. but then...
Hi,
I am new to nrf and trying to make some new services and characteristics for my device.
I followed the advertising , services and characteristics tutorial and was...
hello there i have ble_uart code . when i run on nrf51 dk and when i see it on mastercontrol pannel app. i got that type of screen shot!!
means when i write into characteristics...
NRF2460 is linked，I can transfer 3 byte data. But sometimes it is mute, not always.
Register I2SCNF_OUT bit6 is zero.
I am appreciate for your advices.
I have problem to start the wireshark with this plugin error. The last I checked the nordic_ble.dll file is there in the folder.
The procedure entry point new_creat_dissector...
Hi, I'm new to Nordic. I can't get 250Kbps working on the nRF24LE1. I'm using the enhanced shockburst examples in the nRFgo SDK (enhanced_shockburst_ptx_nrf2 and enhanced_shockburst_prx_nrf2...
Hi, I have an nRF24LE1 based sensor, transmitting to an nR24L01+ connected to an arduino (i know you don't supportit). I have LE1 to LE1 TX/RX working (as a test case). I...
Is there a way to disable (not use) the peer manager's whitelist without setting it to NULL? I'd like to be able to temporarily disable the whitelist without potentially losing...
Hello,
I'm sampling the ADC using PPI like in the saadc example of the sdk12. For the ADC I use
TIMER 1.
And I want to write those ADC values on a SD Card over SPI...
Hi,
I am interfacing micro SD card with nrf52 using fatfs example in sdk 12.0. As I am beginner, first I wanted to perform operations like read, write, delete and some...
I have erased my J-Link firmware in error! after having installed the version supporting V6.12a, however that upgrade wasn't achieved via the drag and drop process.
Where...
Hi,
I am looking to test the performance (range, data throughput, packet drop rate etc.) of BT5 in application specific setting using nRF52840. Ideally this would be done...
