Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Looking for an example to adapt into my program.
I detect 'smp_svr' but compiling it give me error, it seems I need a flash configuration in file pm_static.yml, but I have...
Dear Nordic Support Team,
We are currently developing a new product utilizing the nRF9160 LTE-M module.
We are in the process of acquiring CE certification for our end...
Hi,
I have been facing issues with the configuration of the nRF9151 for sending and receiving UDP packets via the Skylo NTN network.
I am running firmware version:
...
Hello, on my nrf54l10 I observed a pin (GPIO 1.03) being actively driven low for ~20 ms during a reboot (e.g. Resetting after SystemOff Mode). I need this pin to stay high...
[5/10] Performing build step for 'peripheral_lbs' ninja: error: '/index', needed by 'zephyr/include/generated/ncs_commit.h', missing and no known rule to make it
FAILED...
Since a while back ( github.com/.../999b6a14a4556f16d2f535207a84ceb2cca54f8a) the west flash command with --erase was changed so that --erase would also erase external flash...
Trying to migrate from SDK v2.7.0 to v2.8.0 and suddenly getting the build error
Based on other forum posts, I was able to track down more information using the <build target...
Hi, I just got two nRF52840 dongle and it works great as BLE sniffer.
I want to send continuous BLE data (not only advertising) packet and sniff packets between bonded devices...
Dear Nordic Team,
I am currently working with the nRF5340 DK and would like to know whether it is possible to read or retrieve the Network Core firmware version directly...
Hi,
I am using NCS 3.2.1 and nRF52840-DK's version 3.0.3.
I flashed 2 boards with the openthread/cli sample.
From the CLI on both boards, I issued the following commands...
I’m trying to transmit a payload of up to 2,450 bytes using CoAP over OpenThread. Before jumping into firmware development, I want to evaluate the feasibility of transmitting...
Hello DevZone,
I have some questions about nPM1300. I know that nPM1300 need a battery pack that already contains a PCM.
When the PCM activate the protection due to overdischarge...
Hi,
I'm using the nRF54L15 (custom board, nRF54L15 DK base) with NCS v3.1.0.
I have two UARTs:
uart30 — Shell/console (needs CONFIG_SHELL_BACKEND_SERIAL=y , which...
Hi,
I'm trying to use an nRF5340 Audio DK to communicate with another board via SPI. The voltage needs to be 1.8v. How do I configure my board to do this?
