I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Helo, I have ISP1907 for BLE AoA.
In my understanding, the antenna spacing should be half of wavelength, in case of BLE, it would be 2.4GHz thus the spacing should be 6...
On a new board based on nRF9160 I am having trouble figuring out how to bring up the board.
I am using Azure IoT hub and can successfully build an application that can connect...
Hello,
I want to use the bq274xx.c sensor library. The bq274xx battery fuel gauge has an interrupt pin, which would allow to have the CPU idle until something interesting...
Hi there,
I'm using a slightly modified version of coap_client to test out network connectivity with a 1nce SIM card (USA). Essentially, I've modified it from a GET request...
Hello
I'm new with zephyr environment and I want to use littlefs in order to partition an external flash over spi, and to be able to upload file over BLE by using a SMP...
Hi there everyone I am new in nRF development. I was recently trying to add conexio stratus pro but i could not find it in my VS extension. What could be the issue?
I used two development boards with 52840, Two development boards are running 'first' and 'second' in the '\examples\802_15_4\wireless_uart\secure', respectively.
Additionally...
Hi,
I really like the new Zephyr conn_mgr, it is really easy to use, almost UNIX like. I am wondering what is now the best way to control PSM. Will CONFIG_LTE_LINK_CONTROL...
I have a timer int callback like this:
void pwm_all_handler ( nrf_timer_event_t event_type , void * p_context )
{
if ( event_type == NRF_TIMER_EVENT_COMPARE0) {
...
I am trying to external target using the nRF54L15DK and I get the following error.
Error: Failed with exit code 1. Failed to device info one or more devices: * 1057767167...
Hello everyone
I need to install Nrfutil offline, computers may not have access to the internet, i follow this istruction and prepare the offline directori whit the comand...
Hello everyone!
I have a question about flashing firmware to a PCBA with the nRF54 and nRF91, or any dual MCU board in general.
When looking at the Thingy91(x) this...
Hi everyone,
I have a custom board using the NRF9161. Its hardware is loosely based on the design of the Conexio Stratus Pro and I’m using the Stratus board definitions...
Hi Team,
We are using nRF9160 modem and SDK 1.7 version with Segger Embedded Studio.
Using at_client sample code, observations as below.
1. Tried to read APN configuration...
Hi,
Is there a way to reset the uptime after doing a reboot? Rebooting the device by resetting the power does reset the uptime, however we need a way to initiate the reboot...
