Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
I'm beginner in the bluetooth environment so I don't understand everything in it.
For my project, I need to develop connection betweeen a BL652 and a smatphone.
In a first...
Hi,
For both (nRF52840 / nRF52832 ), with SDK version nRF5_SDK_15.3.0_59ac345
I am using Secure_Bootloader in the eample folder:
nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral...
I found an issue when using CONFIG_AZURE_IOT_HUB_DEVICE_ID_APP to set the Azure Device ID.
Around line 88 of azure_iot_hub.c the "user_name" structure is set using the...
Hi,
Is it true to say you have two modem firmware streams: 1.1.X and 1.2.X? Are these two kept in sync in terms of GNSS improvements? I notice the 1.2.2 release notes mention...
Hello,
I want to measure current consumption of nRF9160 of the Thingy 91 with the Asset Tracker application in PSM mode without GPS. For that, I added to the function modem_configure...
Hi,
Browsing the API I only saw Enhanced shockburst support. I need air compatibility to an old 250kBit plain Shockburst communication. No auto ACK and no auto retransmit...
I have run up the CLI example to test as we will require some command line interaction and why reinvent the wheel?
I run up the example with USB enabled and UART disabled...
Hello Nordic,
I try to establish communication between an ATmega328 based board an an Arduino Nano, so far without success. The goal is to improve a RF433 "Wire". 3 weeks...
Dear All, I am using the ADC to measure 3 voltages applied on different ADC inputs and 3 different channels. My ADC configuration looks like this: And this is how I am performing...
Hi,
I recently acquired the nRFgo starter kit and nRF2724 rev 2.1 and the nRFgo development kit. I have downloaded all of the supporting software that were found here...
I have the latest nRF Connect for Desktop.
After I install "nRF Connect SDK v1.4.99-dev1" in Toolchain Manager I don't have an "Open IDE" button.
I've tried uninstalling...
I am adding JLINK_MOITOR.c and JLINK_MONITOR_ISR_SES.s and add write
#if CONFIG_JLINK_MONITOR_ENABLED NVIC_SetPriority(DebugMonitor_IRQn, _PRIO_SD_LOW); #endif
at starting...
Hello everyone,
I'm trying to develop an application with BLE, using an example as a base.
The advertising is good, well configurated, I can edit manufacturer specific...
I am currently using Mesh SDK 4.2.0 and I could successfully write and read reliably from the flash using a second flash manager instance used in parallel with the flash manager...
