I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi all,
I have a question regarding the difference between the nRF51822XX AC and nRF51822XX AA during the configuration of IROM and IRAM in Keil software.
I know that...
To the kind attention of Nordic support team,
We are going to use nRF52833 in our products, and we would like to embed in our PC side software (driver) a custom version...
Hi there,
I'm developing a custom board that integrates a NRF52840 based BLE module from Raytac. I was wondering if it is possible to upload the Adafruit nrf52 bootloader...
Hi,
I am implementing LESC on nRF52810 using an example.
Unfortunately, I didn't find any examples.
So, I am programming the PCA10040e with reference to the PCA10040...
Hi,
I am new to NORDIC dev and I find its ppi is really useful but also difficult to understand.
Now my device may be connected the truck engine to count the engine speed...
Hello Team.
I have NRF52840 Development Kit. here is description, what I want to do and How I am doing.
I will send command on terminal and kit will start scanning for...
Hi,
I developed a product using nRF52810 and am now preparing for mass production.
However, since I have no experience in mass production of Bluetooth, I would like...
Hello my current setup use :
nRF52 dev kit
Segger Embedded Studio V4.4
SDK160098a08e2
s132
nRF connect on a iPod touch
I can compile and once connected appreciate...
I am looking for example code on the EV-BT840(832)-V4 dev kit. I can program it with the hex file and it works, but when I program with the nR52 SDK example codes thru Segger...
I am trying Bluetooth mesh light-switch application on microbit, and I have flashed with same light code on multiple microbit devices, Though all the devices are getting detected...
Hi! I am currently writing a DMA driver for UARTE which with the goal of being able to handle large data transmissions with little software intervention as well as handling...
Hi Team,
We are using nRF9160 DK, We tested the asset tracking application with the DK. It is connected to nRF cloud and the data is sent from the DK to cloud. This is...
Hello, I am working on a script on Jlink to be able to flash from my raspberry. I used to have a batch script using nrfjprog and I didn't know how to translate these commands...
Hello!
I have both SD Card and accelerometer in same SPI bus. Both of them working like charm if another is not present. I'am using app_sdcard from 52 sdk.
Can i use spi...
Most of the SDK Peripheral examples support only a single connection.
Is there a guide somewhere which explains and illustrates what, exactly, needs to be changed to update...
