Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
hello：
I want to communicate with my nrf25U1 USB dongle. So i add some code（refer to the examples\proprietary_rf\gzll\gzp_desktop_emulator）. When i add add these files(nrf_gzp...
Hi, Everyone
I am developing with SDK 15.3.0 and nRF52832
Compiling "examples \ secure_bootloader \ pca10040_uart_debug" and "examples \ secure_bootloader \ pca10040_uart...
I can't find anything on this error on Nordic support or Segger support sites. I've looked into the obj directory and only find one main.o file (of course!). Can't see anything...
Hi. We are using a BLE module based on Nordic nRF52832 in a new product we are developing.
The nRF52832 & softdevice has its own QDID - 115277.
However the module also...
I am trying to get a project working with a main.cpp file, some C++ modules, and the 16.0.0 SDK using the IAR compiler. However, using the nrfx/mdk startup files, it never...
Hi,
Iam running the BLE uart and Zigbee light multi protocol example. Using the latest thread and Zigbee SDK v3.2.0. The example is quite good. That the door(Zigbee+BLE...
Hello.
I would like to make simple GPIO bridge. That means transmitter with Digital input and receiver with digital output. When the state of DI changes, it's transferred...
Hi everyone,
I am using nRF52 DK with 52832 on it. My current SDK version is 15.2.0. I know that for IoT applications there is external hardware needed as router like RPi...
Hi,
I have a problem with a specific Zigbee certified device that I can't connect to my Nordic device.
When trying to connect to the device, I go to see the status:
...
Hi,
In need to debug my application using segger IDE when there is bootloader already present in nrf52832 chip .
The sdk we are using is SDK 15.3
Bootloader:- "secure_bootloader_ble_s132_pca10040...
Quick project overview:
Mesh network using nRF52840.
Nodes need to be able to be controlled individually (setting GPIOs) and also report back data (ADC, GPIO state) to...
Dear sir/ madam,
I have two questions regarding NRF52832 as follows:
1. Will nrf52 only get connected to apps provided by nordic? I want to it to get connected to serial...
Hi,
Greetings!
I am using following setup
1. Mesh SDK: 4.0.0
2. SDK 16.0.0.
3. Segger Embedded Studio on Windows 7
I had a look at "pwr_mgmt_pca10040 " example...
I slightly modified the qspi example code to try something that I'd eventually like to implement as part of my application. But when I try to interleave reads and writes then...
Hi,
We did stumble upon an issue with our BLE peripheral running on an nRF52832 with Softdevice S132 5.0.0 . The central side is implemented on top of the UWP (Universal...
