Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi
I made a custom board. (using nrRF52832)
At frist, I tested my code on 52DK(PCCA10040). It is worked.
And then I tested my code on custom board. I changed my code...
Hello,
Sorry for simple question. (Yup, I'm Canadian and we say sorry a lot!) I have SES 4.18 and nRF5 SDK 15.3.0 installed on my Mac (10.13.6) and cannot get logging (NRF_LOG_INFO...
Hi! I am using the MQTT simple sample that i have modified to continuously send data after receiving a message. I also have connected a MS5837 pressure sensor to the nRF9160...
I'm trying to get DFU OTA working with SDK 14.2.0, SD 132, on the nRF52832. I'm using the bonded implementation. My DFU event handler is getting passed
BLE_DFU_EVT_BOOTLOADER_ENTER_FAILED...
So I want to run the nRF52811 chip so I removed the nRF52832 chip from its development kit and soldered the nRF52811 chip but I cannot seem to program it. What are the required...
Hi,
I am using ncs 1.0.0 and modem fw version 1.0.1.
I am using PSM mode in my firmware.
I want to toggle state of one gpio when modem goes in active or inactive state...
Hi.
I am developing application with mpu6050 gyro on nRF52832, swd S132 V6.1.1., sdk 15.2. My code is based on ble_app_uart. In main, I add my custom function that calculates...
Hello!
I was going to start to program my Thingy 91 but since I don't have a J Link Programmer cable or a nRF9160 DK. I was planning to use mcuboot like suggest this documentation...
Hi,
I am working with MPU6050 gyro. I run the examples from GitHub for nRF52. Everything works fine, bit I have an issue with gyro output data. In register map documentation...
I'm new to Nordic, I just got an nRF 52 DK. Refreshingly simple to get working with Segger Embedded Studio on Mac. I'm particularly interested in the BLE multiperipheral application...
Hi,
I'm trying to build the asset tracker off the master branch in windows 7. I did do west update. Using gcc version 7.3.1 20180622
It fails like below. Any ideas?
...
Hello,
I have the following issue. I am developing an application very similar to the "ble app hids keyboard" example. SDK 15.0, S132 V6.0.0, nrf52832.
I would like to...
Hi!
Previous tickets 234795 and 231307 asked about the status of field updates of the nRF9160 modem firmware. Some solution is coming, but unclear when.
Are there any...
We are developing with the nRF52840, in this instance present in a Laird BL654 module carried by their DVK-BL654 dev board.
After trying three separate examples that attempt...
Hi all,
I need to be able to reprogram an nRF52832 on a daughterboard from a mainboard with a Cortex M7. I have been able to eraseall and reprogram the nRF52, but it seems...
