Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Dear,
Firstly, I configured the GPIO pin 9 and pin10 as GPIO by defining the CONFIG_NFCT_PINS_AS_GPIOS in my project.
And in my project, button1 uses GPIO pin 10 and button2...
I have successfully run the SAADC example, and make it a multi-channel example. I see the function saadc_callback(nrf_drv_saadc_evt_t const * p_event) which performs the printing...
Hello,
I have a trouble handling new chip nRF52832 I recently changed.
what I previously used is nRF51822, and there wasn't that kind of problem.
I'm using my custom...
Hello!
I'm attempting to flash a Thingy:52 with the Thingy firmware using Segger Embedded Studio. At this point, I'm just trying to replicate what comes on the Thingy...
I am trying to get Interrupt from UART Rx, so that if any data is received on RX pin it will go to its interrupt routine, but I am unable to find any interrupt routine that...
Hello,
While developing on the nRF52840, we noticed recently that the IRQ priorities that we find in app_util_platform.h (from SDK 15.2.0) differ from the ones we can...
Hi i'm a newbie in nordic chip. Can someone please explain to me that how to enable and disable sleep in nrf51822 and what kind of setup need to be done?
Example in Arduino...
Hi all,
I'm currently working on adapting this example to fit my needs for testing a Bluetooth Mesh network.
I want to add the functionality for nodes to send to each...
Hi All.
I am aware that the USB nRF52840 Dongle does not support debugging but, can this device issue AT commands to a remote nRF52840 module in order to check the value...
Dear,
After adding the peer manager module of the SDK 15.2 and some other codes about configuring static passkey in the example "ble_app_uart" in ble_peripheral, I can successfully...
Hello,
I just install the nRF sniffer and have some trouble.
I use the following software version :
- Wireshark 2.6.4
- python 2.7
- pyserial-3.4-py2.py3-none...
Hello,
I am currently sampling SAADC every 1ms using PPI. Samples are collected in predefined buffer, and then send over BLE with ble_nus_data_send() function.
I would...
If I use sd_app_evt_wait() or nrf_pwr_mgmt_run, I lose TWI. In other words, in order to use TWI, I need re-initialize it. If I use:
__SEV(); __WFE(); __WFE(); It works but...
Hi,
The NRF52DK we use is interfaced to a capacitive touch keypad and an RGB LED. The board works fine when supplied by the USB but when we try supplying through the external...