Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hello,
I am working on ota ble_secure project. I have created a zip file which is the last step and copied this file to my smart phone so that I can upload it using nrf toolbox...
Apparently you need to set the CCCD handle of your target characteristic to enable notification. Problem is, how do you do that? I now know at least 2 ways to do that, one...
Hello!
I am using application that support ANT+ and BLE, so i am using s332 softdevice.
now I want to add BLE bootloader feature. (send .bin via BLE). but in SDK v12.2.0...
I am using the nrf52 development board, when I try to connect to one of its pins a signal from a sensor that generates an interrupt signal every 1ms the programs stops or...
Hi,
I have relay board which is attached to the SoC module nRF9E5 and also microchip serial SPI EEPROM 25AA320 is also attached.
I have the EEPROM programmer and I am...
Is it possible to connect more than one device over bluetooth to single router (Raspberry Pi 3 under archlinux)?
I connect using commands:
echo "connect 00:4D:25:16:1A...
Hi Nordic team!
In my company project, we are using the NRF52, and, apart of other peripherics, we need to use the NFC.
As the NFC isn't always exchanging data with the...
Hi all, As I known sdk13 have bluetooth 5 features that means we can send more than 31bytes in advertising data (8xdata) right? I'm using nRF52832 and softdevice s132 v5.0...
hi,
i'm not able to have the nRF24LE1 go to sleep. I'm using the example at the link below, to which I've added code for UART and ADC usage. Is there a way to end the...
hi
i am working eclipse for setting up projects for nrf52832. When i build the blinky example there is no error but the headers nrf_delay.h are not include and the LED_LIST...
Hi,
I want to write flash using received data in BLE interrupt handler(on_ble_evt()).
When i received some data from BLE, i try to write it to flash and wait until done...
Hi
I'm trying to use the nRF52840 USB Serial UART device (aka USB CDC ACM) however I can't find a Windows driver for this device
The VID is 0x1915 and the PID is 0x520F...
I need to copy a string, but i don't know how to define nor how to copy.
This is the string that i have to copy dev_name.p_data.
I use soft device S130 in NRF51
