This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Is it possible to get the Build Type from the Factory information configuration registers (FICR)?
From https://infocenter.nordicsemi.com/topic/comp_matrix_nrf52832/COMP...
Hi
I have some question about OTA .
1.The nRF SDK hvae twos way for OTA: single bank and dual bank;The nRF Mesh 3.10 too?Because my firmware maybe very large,so I want...
Dear all,
I am having issues with service discovery of two primary services ( Battery and one propriotary based on NUS) I am currently using SDK 14.2 on NRF52832 chip running...
Hi, I'm trying to use the Seggar Embedded Studio to debug my code, but the Seggar Embedded Studio can only recognize the nRF52840 development board, not the external device...
Hi,
On my previous question https://devzone.nordicsemi.com/f/nordic-q-a/47762/certification-when-bt-off ,
I got the answer about certification.
And now, I want to...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
I am using the Power Profiler app that is part of nRF Connect. This app was working just fine, but this morning I did the upgrade to v.2.7.0. Now, I am unable to control the...
Hi, guys. I copied the EAGLE schematic and PCB drawing file from the SparkFun nRF52832 Breakout design for my custom PCB (4 layers, FR-4).
https://cdn.sparkfun.com/assets...
We want to control the BLE Mesh network from the linux. As we understand the only one way to do it now - pyACI https://infocenter.nordicsemi.com/topic/com.nordic.infocenter...
Hi all,
We develop a custom board using MCU nRF52840(Master) and Module nRF9160(Slave).
I confuse to select an available circuit configuration from the reference circuitry...
Myself and others have received this error message
while upgrading nRf Connect for Desktop.
Despite the error message, the installer seems to have completed correctly...
I'm using an NRF52840 custom board along with FreeRTOS and soft-device S140 V6.0.
I want to access the complete 256KB of RAM for verification of RAM using a custom protocol...
Hi I'm considering a design with this precision RTC
I intend to use the 32KHz output on XL1 (and XL2 grounded) as I've seen done here, but the DS3231 datasheet says the...
On both the 51 and the 52, I believe the reset pin is active low, and should otherwise be tied to VDD?
The reason I am asking is that I failed to find this information...
Configuring the GPIO with the following parameters giving me the 3.3 volts on the pin 26.
Is there any way to bring the voltage down to 1.8V through software ?
