Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hello,
we have custom boards with nRF52832 chips, which show different behaviors in low power system ON mode. The current consumption is pulsing at around 22Hz to ~34Hz...
HI.
I purchased the nRF24LU1 + chip and created a USB Dongle module.
I have come to know about PID and VID.
Can I use nordic's VID (0x1915) as it is?
Is USB Dongle...
Hi ,Nordics
when I use my host device (reffered to the example of ble_app_hrs_c)to pair and bond with a peripheral device(a gamepad) ,the pairing failed .I don't kown...
Hello....
Is there a way to configure the SPI peripheral(s) to run at a custom bit rate (frequency)?... For example: Run SPI at 3.4MHz.. or any other custom frequency that...
Hello all,
Do you advise to have 2 SPI interfaces - one for the sensors we're using (accelero/ gyro) and another one for the SD card? if so, when adding an SD card to our...
Hi team,
i am having a custom board i want to program soft device and application using external j link. i came across nordic website in this page http://infocenter.nordicsemi...
Hello All,
I am a beginner to NFC OOB, so can you suggest me some good learning materials regarding NFC OOB pairing as I wish to do so between my mobile phone and the...
Good Morning Team,
Hope your day is going well!
Could you please provide the IPC 1752 document and RoHS CoC (2015/863/EU) directive document for below part since it is...
hi hi ;
i'm trying to control gpio pin 20 with my smart phone and with event at gpio pin 5 (when the state of the pin 5 changes the gpio pin 20 toggeles ) but my problem...
Hi, can someone explain in simple terms how it works?
I don't really have a clear concept of what a replay attack is, but I suppose it has something to do with recording...
Hi,
I am facing the same issue for all of the node.js examples.
It says: Connected! Error: command disallowed (oxc)
Also is says: Service uuid XXXXXXX not found!
...
The nRF52 SDK ANT example "ant_scan_and_forward/" configures a device linit of (16-1)=15 in this line:
// Public Definitions #define MAX_DEVICES ((uint8_t) 16) /**< Maximum...
On nrf52832 and nRF5 Mesh1.0.0
When running idle state(not RX/TX), current comsumption is over 400uA.
And every 100ms, CPU is wake up.(small working.)
What happen...
Hello! I am using application that support ANT+ and BLE, so i am using s332 softdevice. now I want to add BLE bootloader feature. (send .bin via BLE). but in SDK v13.0.0-1...
Hello.
Which application can I use to monitor and configure a smart wristband with nRF52832? I would like to check its firmware, update it and see all the info about the...
