Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
We would like to achieve following:
Only peripheral devices should advertise data toward only central devices in the same application.
advertising data by peripheral...
Greetings! I'm trying to set up an nRF52 board as an SPI slave so that it would receive chunks of data irregularly from the master device (a Raspberry Pi in this case, if...
Hello,
I would like to know how to implement middle button click in hid mouse, by middle button click i am referring to scroll wheel click and the function associated with...
Hello!!
Is UICR.CLENR0 register disabled on nrf52SoftDevice?(only nRF51Chip??)
When writing with nRFgoStudio("Enable SoftDeviceProtection" CheckBox is on), the firmware...
Hello,
We are trying to build asset tracker based on a modification of board nrf/boards/arm/nrf9160_pca20035.
Every is good until we tried to enable secure bootloader...
Software : C / GCC - SDK 15.0.0 - SD140 6.0.0 - building on multiple platforms. Hardware : nRF52840-DK (Q1AAC0) - and secondary testing on custom board using the Fanstel BT840...
I have been at this for a few days now, I have had a number of compilation errors that I have had to work through and find solutions for, but I am stumped on this current...
I'm trying to use the low-power comparator.
I've started up the comparator using "lpcomp_init()".
Following that, I wish to have a sample event, and then log the result...
I am trying the example here: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_att_mtu.html
I want to lower the sleep...
Hi,
How do I enable Band 1 on my Thingy 91? On your web-page it seems that your base-band supports Band 1, but when I use the following AT-command AT%XCBAND=? I get the...
we are building some IOT devices for home automation, and things were going quite well since we tried to use our mesh network with two cell phones. we tried with two devices...
Hi.
I am using the NRF (Nrf52840) dongle to operate BLE devices (scan \ read \ write).
Is there a way to do it without the NRF connect application and just sending serial...
Hi,
I used Power Profiler Kit to measure our Custom module's current consumption. Everything worked perfectly.
Then I closed PPK SW and used SDK to flash new SW to one...
Hi,
I have connected nrf9160-dk to my laptop and using nRF connect v 2.6.2 with LTE link monitor application.
I am seeing only UART in green and Modem in Red. I am thinking...
