Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
I would like to use AT commands to get the IMEI on a custom board that has an nRF9160.
In preparation for this I am attempting to get AT communication working on a NRF9160dk...
On the nRF52811 with the s140 softdevice, what is the set of things to do to enter very low power sleep state? The product specification says ION_RAMON_RTC is 1.5 μA. What...
Hi
there I'm having a problem in compiling an application using nrf_esb and app_timer.
./nRF5_SDK/components/properitary_rf/esb/nrf_esb.c:900: multiple definition of...
hi all, i'm trying to disable uart for lower power consumption, i've disables it with: but when i measure the voltage on the rx pin i see 1.8V (this seems to consume current...
Hi,
I'm starting with nrf52 dk using Keil ide for ANT+ applications...
I tried to run an example inside the sdk folder and I have problems with app_error functions....
I have been running a mqttsn client publisher/subscriber project (based on the example) successfully for some months. I have added a mosquitto broker to the raspberry pi border...
We are designing BLE products based on the Nordic nRF52840 chipset and star network topology which are used indoors, according to the network structure, we use one Master...
Hi everyone!
I've been using the Power Profiler Kit quite successfully for the past few months. Instead of using the UI, I designed a python app to communicate with it ...
The nRF52840 OPS 0.5.1, describes nWRITE,BLOCK as the amount of writes allowed in a block between erases, and lists nWRITE,BLOCK = 403 Maximum.
It looks like 8 blocks are...
Hi folks,
I have a system basically working with the following setup:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) #define MAX_CONN_INTERVAL MSEC_TO_UNITS...
adv interval : 1s
adv data: 31byte
tx power: 0dBm
MCU: nRF52832
The power consumption is shown in the figure below,when I don't enable DCDC.
what may be the reason...
I followed all the steps mentioned in the tutorials. In one of the threads, it was mentioned to erase all and then try and it worked for some. I tried that as well. Still...
I'm using nRF Connect v2.6.2 on windows 10 using an nRF51 dongle to update my target OTA. Target is an nRF52832, softdevice s132 v6,1,1. The DFU process takes like forever...
Hello,
I work in a startup, and we aim to measure cooling conditions in data centers.
For that, we have developed customs boards with a nRF52840, and we are using Bluetooth...
Hi, I am currently using Nordic nRF52 dev board (with nRF52832 SoC) and trying to test "dfu/secure_bootloader" example in that board. Because my target ship is nRF52810 I...
