Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
We have vibrator connected to gpio pin 18 on the nRF52832. Controlling it works fine in the application but as soon we enter DFU the vibrator starts and it doesn't stop until...
Dear Nordic Team,
Is it possible to use the nRF52832 for MCU application only, without the BLE stack. Can the application code use the complete memory of the nRF52832. ...
hi.......
i am facing the issue while i am transferring the data via ble to ble_app_uart ...
i am using nrf52382 and segger 15.2v
Here if send the one data over ble...
I use SDK12.2.0. The mobile phone has connected my 51822 device,and then the mobile phone keep away from my 51822 device till to disconnect.how to do that they will connect...
Hi Guys,
I facing issue on one of my project, our HW require 2 set of TWI and one QSPI/SPI. I notice SPI0/1 cannot be used because I need both TWI0 and TWI1 to be supported...
Hi,
I'm trying to adopt my nRF52832 projects to the nRF5 SDK version 15.2.0 and the NRFX drivers framework. I'm using a short app_config.h with NRFX_RTC_ENABLED and NRFX_RTC0_ENABLED...
Hello,
There is a example for the nrf52840 for thread with mqttsn. Although this is just for my personal use I would love to use some kind of encryption for it.
So the...
Hello. I have been trying to work with extended advertising between two nRF52840 boards using the SDK, but have had trouble in setting a long advertisement payload (as in...
I followed Einar's nRF52840 Dongle Programming Tutorial and tried the ble_peripheral/ble_app_eddystone example using SES 4.12. Opened the project, changed the preprocessor...
Hello All,
I have been using this NRF52 DK board with KEIL for like 2 weeks. I read the all the document regarding BLE 5 protocol and followed the DIY codes step by step...
Hi Sir,
In this project, we design with nRF51822-QFAA (Flash: 256KB, RAM: 16KB) and developed the application and bootloader through the nRF51-DK (pca10028). The file...
Hi Sigurd,
Thank you for your reply. I have executed the code given by you (below link) in Segger studio(V 3.50) I observed that the output or load (pin 31) which is connected...
We have the device, where 2 power supplys can be applied. One of them is external regulator with 3.3 V output. We used it for additional load in our device. Another one is...
