Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi.
I think i just fried my NRF52840 dongle. VDD out is only about 0.5V :| I'm currently powering it from the usb port (VBUS is correctly +5v). Could it be that Ii only...
Hi,
I"ve designed a custom board with the MDBT50Q module (part of the schematic below). When writing my program to Flash 0 and Ram Memory 2000 0000, the program won't load...
I have been experimenting with the example of the MQTT Client Subscriber/Publisher from de nRF SDK. I use:
SDK v15.3.0 (also nRF5 SDK v15.2.0).
Raspberry Pi 3 (as a...
Are there any working projects that integrate TWI and MPU6050 sensor. That are edited by KIELu5 and follow the SDK 15.3v ? I tried modifying the 'twi_sensor' project but I...
Good day
Im trying to switch off an LED when my relay/hopper is not advertising. I switch the LED on successfully when transmission starts but I'm struggling to do the sd_ble_gap_adv_stop...
Hi, everyone,
now I'm test " \ncs\nrf\samples\nrf9160\gps\build_nrf9160_pca10090 ",
it's error about" nrf_socket.h: No such file or directory"
I'm find the file at ...
So this is a small continuation of this ticket https://devzone.nordicsemi.com/f/nordic-q-a/50656/using-pdm-mic-on-nrf9160dk .
The problem I'm having now is that when I run...
I wrote UART echo sample based on ble_app_uart_c for S140/ nRF52840-DK.
When nRF52 receive one line on USB/UART, it send same line to USB/UART.
I also write Linux socket...
I am following this tutorial:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development-kit/posts/application-timer-tutorial?CommentId=43347679-22d9...
Hello,
I want to use the ADC for a burst @ 8khz.
I use this sample " test_adc_sample_with_interval " from https://github.com/zephyrproject-rtos/zephyr/blob/master/tests...
Greetings...
Please help me understand why PB-GATT support is removed from SDK UART coexistence example?
The dilemma I am facing is as follows:
1. No PB-GATT for SDK...
Hello, Currently, we trying to use PPI with the SPI module (we use the SDK 15.3.0) We expected that the SPI makes one read transaction every 5 us ; to do this, we use 2 PPI...
Hi there,
My project needs TrustZone and ETB feature. The manual clearly states that the board supports TrustZone and ETM. I wonder if it also supports ETB to store trace...
Hi,
I am using SDK15.3 with the SoftDevice enabled. I've been unable to get any SoC events after making a call to sd_flash_page_erase. I registered my observer as follows...
