I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
hi to everyone!
I am using nRF52832DK with Keil5 and nRFgo Studio to program SoftDevice.
Now I want to program my first custom board, but it looks like I can't connect...
Hi,
I checked the errata document for nRF52832 Rev.2.
In #182, there is the sentence of "Improvements as described in IN #105.".
However, I can not find the #105.
...
Hello!
I experienced the same errors as here and here when following the Eclipse gcc tutorial (7), but the solutions did not solve my problem.
I suspect this is related...
Hello ,
I use nrf52832 in my custom card, I developed everything on the develeppement kits nrf52, and when I merge to the custom card, I remerque that there is a huge consumption...
Hi Sir,
We have designed custom nRF52832 board in PCB design layout have 4 Pin connector VDD, SWCLK, SWD, GND. I know how to use nRF52832 DK for programming. But for other...
Hi,
I am using SDK12.3 and stack s132 with NRF52832. We have to store 3 variables in flash memory and keep updating it once BLE connection is formed with the phone. We were...
Hi,
I use nrf5_SDK_for_Mesh_v1.0.1_src SDK to debug mesh in SEGGER Embedded Studio for ARM 3.34. The projects are all based on NRF52832, but I want to debug it on 51822QFAC...
Hi,
I have been using the following parameters to flash program the example ble_app_uart_c_s130_pca10028 (SDK 9) but the problem is the it uses the S130 v1.0.0 softdevice...
Hi,
I have a newbie question. Is it possible to implement a POTS voice quality like an intercom system using Thread (assuming all the end points are using nrf52840 SOC...
We are trying to minimize the UART current in our product, so we tried some experiments on the PCA10040 board.
We noticed a significant current difference between SDK11...
SDK14.2.0 sd132v5.0.0 nRF52832
I've looked for a solution to my issue on the discussion forum, but can't find an answer. I am working with the buttonless DFU peripheral...
I have two nRF52832 devices. One of them I have been using for a while and the other is brand new. My BLE application will flash and run just fine on the old device but not...
Hello,
I read in your datasheet the follwoing:
"32.768 kHz synthesized from HFCLK (LFSYNT)
LFCLK can also be synthesized from the HFCLK clock source. The accuracy...
Hello,
in the Online Power Profiler , the current consumption increases, when the voltage is reduced. What is the reason for this?
Isn't there any documentation on the...
