Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
i have 3000 bytes of data placed in flash from 0x20000. i want to calculate hmac for the same data.First, can we calculate hmac for such huge data?If yes, then how can i calculate...
I'm using SD 110 and the PCA10001 board.
I make the call to:nrf_gpio_port_read(LED_1), where LED_1 is on, or high. This call always returns a 0. How can I read the state...
Hello!
I'm trying to advertise my custom service. After setting everything up, when calling ble_advertising_init I receive error 0x7.
static m_adv_uuids[] = {0x1523...
Hi,
I ported some SDK code into my device (SDK 10 adapted for S110v7x) where I can successfully Bond my device and use the Services I need (ANCS on my case). I have simplified...
Hello,
I have a project that I want to transfer it from nrf51 to nrf52 (the changes are from nrf51822 to nrf52832). I followed the migration guide. And now it debugs so...
Hi all.
I have phone with nrf Tollbox and central device with DFU, SD130 2.0.0, SDK11.
I would like flash application to central by OTA when I enter password in nrfToolbox...
Hi Nordic,
EDIT: I am using nrf51422, with S210 v5.0.0. Everything that is below is referring to ANT protocol
I want to know if the thing that I am planning to do is...
I download the example of multilink central (S130) into nrf51822 .The central transmit 20 bytes to peripheral interval 50ms sometimes will reset.Anybody know the bluetooth...
Hi guys,
I have the NRF52-DK and want to power only the NRF52. So basically, I want to power it over VDD_nRF.
When I power my DK with a battery and then measure my current...
Hello!
Is it possible to read data sent from ble_app_hrs (peripheral ) to ble_app_uart_c (Central) on PC's serial monitor? If possible, how can i achieve this and which...
Hi,
I programmed nRF52 DK with BLE_APP_UART_SAADC_TIMER_DRIVEN with AIN6 pin as input and is working correctly. But when I programmed the same code in BMD300 the adc count...
I'm running an nrf52832, using SDK 11.0 and the S332 soft device. I've had instances where it seemed my flash data, stored with FDS, was corrupt after a firmware upgrade....
Hi Nordic,
I am having problems knowing what exactly happens in the following situation:
I have a connection established between a master and a slave, and the master...
Hi,
I have started your tutorials and just complement this one. devzone.nordicsemi.com/.../
Now when I tried to download other programs on the development kit, I get...
Hi,
I have wierd experience about using float32_t.
This is my test:
When i use operations on float64_t i got:
0.0001s MAIN:INFO:init_finished
0.0001s MAIN:INFO:loop...
