Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Is there a ready example to run nRf51822 as a controller to external host via HCI commands over UART or USB?
e.g. I want to interface the Nordic chip with an open source...
I am using softDevice S140 with SDK 14.2.0_17b948a, working with the ble_app_blinky.
I need to be able to connect one peripheral device to multiple central devices (peripheral...
I connected via a USB cable my ppk to my computer. But when I fire up ppk.py, it says "no response from ppk. Check power, debugger connection and make sure the firmware is...
Is there any other way of programming the Nordic Thingy other than using the nrf52 DK? Where to get the programming/debugging port's pinout , I didn't find that in the hardware...
After connect devices status GAP Secure status ...->evt.gap_evt.params.auth_status.auth_status 0x0D In documentation absend this code = 0x0D What is It?
I would like to use 1.3 V System power to supply some external circuit that may need max 10 mA. This voltage is available via pin DEC4.
I expect that you are going to...
Hi There, I'm very new to mesh and have a bit of a learning curve to understand the mesh SDK. A few questions for those in the know....
I have been playing around with the...
hi,
can anyone share sample code for getting accel values from MPU9255.?
I have tried with this ,Iam not getting output.
Chip :nrf52382
Board : nrf52Dk - PCA10040...
Hi
How can i configure NRF_LOG with IAR and J-Link connected via USB to a RAK 813 BreakBoard, i'm testing BLE SCAN Application.
Regards,
Julio César Morales bErmúde
Is there a way to modify the code in the ios nrf beacon app to identify nordic beacons?
I am aware that the manufacturing id must be set to 0x004C in order to be identified...
Hello,
Is it possible to create a GATT service with a 128 bit UUID, where each characteristic has a unique 128 bit UUID of it's own?
Looking at the examples, it seems...
Hello guys,
During implementation of a test set for CryptoCell AES CCM* functionality i'm facing some issue with the CryptoCell.
Encryption works fine without any issue...
Hi,
my application application consist of NUS service, one i2c, one spi and one adc. it consumes around 10-11 mA while its running. its was observed that while only running...
I am using APP_TIMER to turn ON and OFF pwm. PWM is used to drive a buzzer. PWM is turned ON and OFF in the APP_TIMER timeout handler.
It is observed that after starting...
I have now spent a significant amount of hours debugging strange problems with my advertising. It turned out that it is very important how you set up the init structure for...
