I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Good morning everyone,
I read a lot of threads in the last week on this subject, but so far I was not able to find a solution to the problem.
On a custom board we are...
Is it possible to use both Zigbee & BLE SDKs at same time? Actually we are planning to use NRF52840 for our next project. In which BLE will be used for Smartphone to NRF communication...
Hi there,
I have suitably designed a battery sampling circuit in my prototype configuration, (Vdd = 1.8V, battery swing = 4.2V to 2.9V) using the app note provided at: https...
I am getting the following error when trying to compile port.c
../../../../../Nordic_Semi/nRF5_SDK_14_2/external/freertos/portable/ARM/nrf52/port.c:93:7: error: expected...
Hello,
Is there any sample code which performs only the most basic functions?
Ie. - Sample code in its simplest form which only sets one pin to an output and sets it...
I'm using SDK 15 and soft device S132 6.0. Using nrf Toolbox to update custom firmware, I'm running into a situation where the DFU update fails with an error code 4 when trying...
Hello,
I have been doing research trying to figure out how to program just the nRF52832 chip. I want to program the nRF52832 chip with the Arduino IDE from sandeepmistry...
Hello!
I am using the nRF2740 board with the nRF8001. If I connect all the pins (SPI, RESET, RDYN, GND) except the Vcc pin I still measure 2.5V at the Vcc pin (Connector...
Hello everyone,
In my current application , I am using nRF52832, with the SDK 11.0. I have a problem with the BLE connectivity, which I think is a hardware issue.
With...
I am doing a connectionless system where I am just broadcasting the data. I am showing a loss of about 50% on the receiver missing the data packets. I have tried before to...
Hello,
I configured pin P1.15 as output and with GPIO_PIN_CNF_DRIVE_H0H1 but I only get 1.7V ?
Does "standard drive" means that the pins can't get to 3V ?
Thank...
My project is based on the Thread cloud coap client example. I would like to know if my CoAP POSTs to the cloud are successful.
I added a "post_response_handler" to the...
Hi,
I've been trying to read/write data from/to the internal flash storage of my nRF52 development board.
I am using SDK11 and softdevice s132
I have modified the flashwrite...
Hi,
I've been trying to read/write data from/to the internal flash storage after a ble disconnect event occurs on my nRF52 development board.
I am using SDK11 and softdevice...
Hello,
i'm developing an interface based on nrf52. The app does a direct connection, performs some exchanges with the peripheral, and tells the peripheral to disconnect...
