Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
I have been able to connect and initialize two different Bluetooth OBD II Devices. I am running into issues with the third device I am trying to add as an option. I add the...
Hi,
nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect
We need to implement a multicore application for nRF54H20. I...
Hi,
I have a question concerning time zone support in nRF SDK >= 1.9.1 for nrf9160.
I'm trying to implement an LwM2M client that should be able to convert a UTC datetime...
NCS 2.7.0/2.8.0
mcuboot + MCUMGR in the application for BLE DFU
NRF52840
We have been developing our next version of our product, transitioning from NRF SDK 5 to NCS...
Hi，
When I used NCS V2.5.0,after two devices successfully establish a BLE connection but then disconnect due to a timeout, subsequent reconnection attempts fail with error...
I have a BLE system where multiple sensors operate as peripherals and send data to a BLE central. These sensors enter sleep mode after transmitting data and later wake up...
Hello,
I designed a PCB using nRF52840 for controlling the board.
I have physical access to the following pins : SWDIO, SWDCLK , VSS , VDD , nRESET.
What is the boot...
Hi,
I'm trying to test DTM over USB CDC with an nRF5340DK unfortunately, Direct Test Mode desktop App is not detecting the DK.
Build command (copied from VSCode output...
Hi, I have encountered issues flashing a NRF52833 board which is on a custom PCB. I have picked the project up from another developer so it is somewhat developed already....
hi,
I am reviewing development in the environment below.
* HW : nRF52832
* SW : SDK -> example -> ble_app_uart_c
In the nRF52-DK board, we reviewed the example...
hi support team,
i want to confirm the FEM control when using nrf21540ek for mesh demo "light" with 52840dk.
i set :
CONFIG_BT_CTLR_TX_PWR_ANTENNA =20
CONFIG_MPSL_FEM_NRF21540_TX_GAIN_DB...
Hello Team,
I am trying to set configurations for FOTA. I refer smv_server sample code and the following document https://docs.nordicsemi.com/bundle/ncslatest/page/nrf/app_dev...
We are using the NRF9151 and unable to establish a connection to an LTE-M network in Ireland (testing in Cork currently). We are using a Kore MVNO SIM which supports Three...
Hi,
I am trying to upload data from two sensors, the BME280 and APDS9960, to the nRF Cloud. I have been able to extract data from the sensors with I2C, but it seems I am...
Hello,
I am developing a new application using nRF52832 and writing and debugging code on Segger embedded studio (Release 5.68) with SDK v17.1.0.
I try to run simple application...
