Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
We've derived a DTLS handshake test firmware from github.com/.../l5_e2_sol
Tests have been done using nRF9151 DK, SDK 3.1.0 and modem firmware 2.0.2.
First we verified...
I'm putting together a project that requires a "large" (1500mAh+) rechargable battery, both because of the desire for long times between charges and to enable powering a peripheral...
Hello Nordic Support Team,
I'm working with the Android-nRF-Wi-Fi-Provisioner library ( https://github.com/NordicSemiconductor/Android-nRF-Wi-Fi-Provisioner ) and would...
I'm using the Nordic nRF52840-DK. I'm having a hard time with logging using RTT. Sometimes it works, sometimes it does not. Usually I get a few runs where it works, then it...
I developed a custom application on the 52840DK and have now moved this over to a custom PCB of my own design. I can compile OK and can start a debug session from "main" but...
I am unable to download the nrfjprog command line tools from your website.
I am using SDKV1.8.0 and Toolchchain V2.0.0. in Visual Studio Code.
When I attempt to flash...
Hi,
I have low power environmental sensor. They raise an interrupt that something was sensed and require to read some registers on the sensor via I2C and run a state machine...
Currently, the nRF Connect extensions are available only on the Visual Studio Code Marketplace. We primarily use Cursor, which is a VS Code fork designed for enhanced AI-assisted...
Hello everyone,
I’m currently working on implementing the PK peripheral using Rust with the SVD files for the nRF54L15, but I’m running into a documentation issue.
In...
have a MONOGOTO SIM card that works successfully with TELIT and THALES modems. However, the same SIM card is not detected on the NRF9151-DK. When I send AT+CPIN? , I get:...
Hi I’m having trouble connecting to my nRF5340 dk using nRF Connect for Desktop (Programmer app). When I select the device, I get repeated errors like:
Details:
...
Hello, I’ve been trying to install Nordic Connect SDK 3.1.0 in VS Code, but the installation keeps getting stuck midway and never completes.
I’ve tried several times over...
I'm bringing up a custom board, working through the peripherals one at a time. Unfortunately, I haven't gotten very far before things started misbehaving. One part of the...
With mfw 2.0.2, AT%RAI supports now also "2 – Activate with unsolicited notifications."
That's verfy useful, but I miss some details in the documentation about the usage...
Hello community,
I am working on a project that requires the integration of the u-blox NINA-B302 module , which is based on the nRF52840 SoC .
I have previous experience...
