Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi,
We are designing a product with NRF52840 QFAA + GNSS. Due to size constraint, we are planning to use Ignion DUO mXTEND for both BLE and GNSS.
The antenna manufacturer...
Hello All,
I am looking to use the nRF52840 for a ZigBee project. I am looking at the ZigBee light bulb example and following a few posts here I got it building. I can...
Hello,
I get the following errors when trying to DFU using a nRF52832 DK and the nRF Connect desktop application.
19:00:36.143
Attribute value changed, handle: 0x0F...
I want to build on the agps sample for 9160-dk
This involves changing the destination and format of outputs to cloud
I saw that multiple GPS hits are consolidated and...
Hi, Dear Nordic & all:
when I prepare to do a DFU example，I get trouble in installing "nrfutil" tool
I sure that I installed it successfully， but when I input "nrfutil...
Hi
I have a nrf52840 dongle with which already been flashed with ot-NCP binary and I want to over write this binary with new binary image[ot-rcp] in nrf connect for desktop...
hello,
I'm working with nRF52840 dongle, i installed nRF Connect for desktop v3.6.1 on ubunto 18.4 and i am using python3. After programming connectivity_4.1.4_usb_with_s132_5...
Hello I'm using Zephyr and trying to update the characteristic value with interval of 50ms. The problem is that the android app nrf connect freezes after I start reading the...
Hi,
I'm trying to run the light_switch sample app from nRF SDK for Mesh.
I have both PCA10056 and PCA10059, and I used both to run some other applications before testing...
Hi. I'm evaluating the nRF52810 chip by developing on the nRF52-DK (based in nRF52832 chip). As noted in this chapter https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17...
We need to work with the PWM, the idea is to set one frequency, duty 50%, and put out these pulses to one pin, we understand how to do that but we need to stop these pulses...
Hi,
I once got the following message while trying to attach a debugger to my network core.
After this event, I haven't been able to program my network core.
I have...
I am looking at the hardware design of Thingy91, where the antenna is shared by LTE and GPS/GNSS. My system will be connected to a cloud (probably most of the time) and track...
Hi,
Our NRF52840 (running 14.2) often takes a very long time to disconnect, from when a disconnection is initiated by the phone. It can take 30s, sometimes even more, for...
