Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
I am using the SDK 17.0.2 to make the advertisement and scanning for the two nrf52840 boards. One unit with extended advertisement only on channel 37 and the other unit scan...
The documentation says that: " By default, threads run in supervisor mode and allow access to privileged CPU instructions, the entire memory address space, and peripherals...
Dear Community;
I am trying to send some data via Lora with a nRF9160 connected with SPI to RF95W Lora module. The transmitter is a nRF9160 with a RF95W, and the receiver...
Hello,
We're piloting updating our sensor beacons RuuviTags to use Coded PHY for better range. The current design has nRF52832, our update would be to drop in a nRF52811...
Hi Nordic Support Team,
I am trying to combine
..\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_s140_ble\ses
and
..\nRF5_SDK_17.0.2_d674dde\examples...
Hi,
I have been looking around the forum and have found conflicting information regarding the existence of a QSPI flash driver and example for the nRF53 on Zephyr. Is this...
Hi,
I am trying to run nrf zigbee light bulb sample provided in the nrf SDK on the NRF52850 usb dongle.
I have sucessfully built "blinky" app sample with NRF Connect SDK...
Hello Everyone,
I am developing one product for the HVAC system. I have Radiator and STM's primary MCU. For development, I need to configure the thermostat cluster ID for...
Dear Nordic Community,
Because of unavailability of nRF52840 we are shifting the work to nRF5340. I have some queries on this topic as follows,
1) Is SDK will be changed...
Hi Nordic Team,
I am new to Bluetooth mesh and NFC. I am working with the device nRF5340 and SDK NCS v1.5.0 .
I have used the sample Bluetooth: Mesh light as a starting...
Hello, I'm trying to use PN532 module with nRF52840 using I2C. the data can be sent, but when it comes to read it, IRQ keeps high, so it reads 808080 .. I added a nrf_delay_ms...
Hello,
Starting with the example of mqtt_sn_client_publisher in the nRF5 SDK for Thread and Zigbee and I want to publish an array of data like this one
in a MQTT topic...
I am trying to send some data from nRF52840 to Xbee via Zigbee In this case, I set nRF52840 as router and Xbee is the coordinator. I use zigbee_cli_agent_router sample code...
Just took delivery of a new THINGY:91 from DigiKey - v1.4.0.
Trying to follow the steps in the User Guide, but when I plug into my Macbook, it's not showing up as a USB...
Hello,
I'm a CS student and I'm trying to work with nRF5340 DK. I'm trying to program the sample network_coordinator (Zigbee) to the board using SEGGER Embedded Studio,...
