I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hi
We are using the nRF52832 chip in a design and try to reduce the cost for the product. I have some ideas to simplify the circuits but have some questions about the capabilities...
After clicking on Raw Data in Nrf connect App I am getting this 0x0201041AFF590000150112233445566778899AABBCCDDEEFF0FFFFFFFFC3. what are 0201041AFF these bytes ? can I remove...
Hi
There is a lot of sleep mode at 5.2.1.1
Could you explain what the different between "ION_RAMON_EVENT", "ION_RAMON_POF", "ION_RAMON_GPIOTE", and "ION_RAMON_GPIOTEPORT...
Hi,
I just added some more data to my iBasis SIM card, but I can't seem to find the receipt for the purchase. Where would I find the receipt for this purchase?
Thank...
Hi there,
I have a few questions regarding the Development Kit hardware design. I just bought up the polygon pour manager. I noticed that all layers except Mid-Layer 2 are...
In the documentation, its suggested that the antenna should have a matching network between the WLCSP NRF52832 and the 50 ohm transmission line that looks like this:
...
Hi Team,
I am working on SYSTEM ON mode with Low power mode also called Idle mode in nRF9160 module.
I was able to go to Idle mode with current consumption of 6uA with...
Hello there,
I created a project a while ago with the SES and the SDK 15.x. For a new Project, we would like to move to PlatformIO. Right now I am evaluating where we will...
Hi Guys
I recently made my own PCB for a project. On the PCB I am using a Laird BL654PA Module with external antenna. All the I/O's work great but im struggling with the...
Hi,
We had met problem at buttonless DFU with bonded information at Andriod set-top-box.
The problem we saw is we can not know when the ATT table is different at andriod...
I'm trying to wait on a single POLLIN event on a net socket, but I'm finding that poll() will still return immediately with the POLLIN event even if it's not set in the struct...
Hi , I am developing a zigbee project using nrf52840 using NRF52 zigbee sdk . I had to do some changes in zboss header files ( zb_config_common.h and zb_config.h ) to change...
I'm using the NRF52840-DK with the SB40 jumper cut, then powering through P21 and measuring with an ammeter across P22. USB is unplugged during measurement. I'm using zephyr...
Hi,
Eventhough I am able to communicate with my I2C slave, this message appear for every transmision.
[00:00:00.709,350]
[1;31m<err> i2c_nrfx_twim: Error 195952641...
