Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
HI
I used nrf51822- EK board.
BLE HID MOUSE - SDK 8.0
`
How to send left button or right button data?
How to modify below method?
static void mouse_click_send...
Hi everyone,
I'm working on a custom bootloader for nrf52840-based board. The bootloader needs to support DFU from an external SPI Flash and also BLE. I was working on...
Hi everyone,
I am trying to use the nrfx_uarte driver. I did the following:
(a) setup driver
(b) setup the event handler
(c) finally tried to send some testing...
I noticed a lot of the early SDK's 11, 12, 13 examples that had the service changed characteristic enabled. I'm using SDK 16 and it seems that most examples don't enable the...
I'm building an LTE device that only needs the GPS, LTE, motion, and button.
I'm trying as the first step to disable all the sensors that are not needed so that I don't...
Hi Nordic When the BLE is connecting, the fs_event_handler hasn't any callback after doing nrf_fstorage_erase or nrf_fstorage_write.
It seems like the storage (nrf_fstorage_is_busy...
Hi,
I noticed that there were changes in some of the priorities in SDK config - these defines were changed from 7 to 6.
NRFX_CLOCK_CONFIG_IRQ_PRIORITY
NRFX_GPIOTE_CONFIG_IRQ_PRIORITY...
Hi Nordic Support,
I am currently developing an IoT application (battery powered, cellular device with a few sensors connected). I have spent the past year building the...
I've read a lot in different posts about this but still fails to wrap my head around this.
We have a device using GATT with a few services, each with a few characteristics...
I am investigating Bluetooth mesh examples, which you presented, and I faced with incomprehension with initialization of struct bt_mesh_elem . Can you explain the meaning...
Does Nordic have an examples for implementing symmetric encryption at the BLE application level? I'm trying to understand how best to start because the Bluetooth LE security...
I have a setup where nRF91 and nRF52 on nRF9160 DK have to exchange ASCII strings over UART. nRF91 runs Zephyr and nRF52 - nRF SDK for Mesh.
When nRF52 is unprovisioned...
We are using mesh SDK v3.2.0, nRF SDK 15.3, nRF52840 DK and SES as our IDE.
We had a mesh network with around 5 devices and after a while 2 of them just stopped sending...
Hi,
We are developing the product based on nRF52840 Chipset for BLE Application. We are using the Segger Embedded Studio ( SEGGER Embedded Studio for ARM Release 3.52a)...
I implemented some NonSecure Entry functions in my app and I've noticed that if I check an object using the cmse_check_address_range intrinsic that the check fails if the...
