I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hello,
the "Developing for nRF52810" user guide in the Infocenter says that to fully transfer a project to nRF52810 the defines DEVELOP_IN_NRF52832 and NRFX_COREDEP_DELAY_US_LOOP_CYCLES...
Hi
i am new with nRF52832. i am trying to run fatfs example program. But it shows Disk initialization failed. what is the reason for it?.
i am using segger embedded studio...
Hi,
I'm using SDK 15.2 & trying to combine hid keyboard with custom gatt service, but it was not advertising. When I debug, it got stuck on the line below with error code...
Hi.
I'd like to use nRF52840 in our project. Can I use the SoC and Zigbee SDK for commercial?
UPDATE!
Have I any limits if I will use SOC and Zigbee SDK for commercial...
Hello,
I follow " Configuring and performing DFU over Mesh" instraction and face with error after trying to transfer new app: "No response after opening COM port".
I do...
Hi,
I am trying to merge dfu with Beacon application. I have added all the required file in dfu example, but I am getting linker error for bsp.o file.
I am using sdk 14...
m_cb.adc_state is set to NRF_SAADC_STATE_CALIBRATION inside the function nrfx_saadc_calibrate_offset(), but the value is never changed to NRF_SAADC_STATE_IDLE, even is the...
Hello
I'm trying connect central to 4 peripheralPeripheral has 3 different customization services. When I connected to 4 peripheral, I encountered the problem of service...
I have a question about "SEGGER Embedded Studio for ARM V4.12".
I want to place the section of the FLASH area arbitrarily. And, for example, I want to place the following...
There is now a TI CC2451 Bluetooth module as a reference. Using nRF connect to monitor the log content, it is found that when the mobile phone is connected to Bluetooth and...
Hi everyone, I have a question about GPIOTE.
What happens if for example, GPIOTE is used to configure a pin to detect a low to high transition, but the pin is already...
Hello
I have a problem with restarting advertising after disconnect event.
There are two scenarios:
In this case everything works fine:
I start advertising
...
Hello,
I started with the template app and tried to do two things on a nRF52832 using Segger Studio:
1) advertise custom service
2) use Application Timer and App Scheduler...
Cannot connect to nRF52840DK board using nRF Connect Bluetooth Low Energy app on Linux (Ubuntu 18.04 LTS). When I choose "Select Device" and choose my board, I get:
"Validating...
We have custom developed board using nrf52832. When I run the example program developed in SDK15.0.0 with Soft device S132 V6.1.1, no issue noticed in running debug mode ...
