Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi
I'm looking for a functional example based on Freertos and nrf52 on SDK11 and SD132. I'm having problems (hard fault) and I've been looking for this example but with...
Hi There
I see there is a Proximity App - is this available for downloading like the beacon App ? for use in xcode ?
Also, in the demo, there was a bluetooth unit that...
I use a android phone as central(Master) and use a nrf51822 as a peripheral(Slave).
The peripheral can send the "L2CAP Connection Parameter Update Request" to change the...
Hi
I have a BLE nRF51822xxAA project created with Keil 5.15, SD 100 ver 802 and Family Pack 803.
I made a new configuration in a new machine with Keil 5.2 and I am getting...
I want to create my own PCB which can communicate with the following Transmitter:
www.hobbyking.com/.../_ 43854__Turnigy_5X_5Ch_Mini_Transmitter_and_Receiver_Mode_2 .html...
Hi! I work with a smart Beacon Kit nrf51822 rev1.0.0, s110 and I have visualised my current consumption. What I expected to see is that my beacon could send in one time all...
We are preparing a project where several mobile phones
with Android OS in peripheral role will be connected continuously to
one nrf51822 with S130. Communication must be...
On nrf51 I was using:
pre flash: w4 4001e504 1
erase all: w4 4001e504 2\n w4 4001e50c 1\n sleep 100
pin reset: w4 40000544 1
Is it still the same for nrf52...
[Edited title]
My application on a PCA10028 board is attempting to send a BLE advertisement using sd_ble_gap_adv_data_set() by going through ble_advdata_set in ble_advdata...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi,
is there something like a makefile for nrf52 out there?
I want to use eclipse and gcc in osx. It worked great for nrf512 but nrf52 has other addresses and maybe...
Hello all,
Lets assume that central bonded with nRF51822 peripheral and than disconnected. If bond is saved on peripheral- ok, cental send BLE_GAP_EVT_SEC_INFO_REQUEST...
When i try to do an update with Nrfutils Under android i get a REMOTE_DFU_OPERATION_FAILED since i added signing.
I created my pem file key with nrfutil.exe keys
i copied...
Hi
I'm trying to get working a project by using S132 v3 alpha. I'm stuck at function sd_ble_enable. This function should return the minimum RAM memoy would need the SD...
Hi Nordic.
So, I am using GAZELL to link a sensor node (PCA10001) to a host (PCA1000)
When the node is connected is should automatically send its address to the host....
