Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
Hello.
I have nRF51822 and nRF52832 boards.
I can use both to capture BLE frames with Wireshark on Linux, and I test that with RACCOON also to capture traffic in terminal...
I'm using the DFU module from SDK 9.0 - I enter the DFU by writing to the DFU control point. Is there a way to exit the DFU and have it go back to the app?
Have seen many good thread explaining this model. But didn't find any full example code for it for client and server Model.
I have tried light switch demo and working fine...
Hello!
So I have a new nRF52811 board which was designed by someone else, that I need to develop some pretty simple firmware for. Full disclosure, the design is based on...
Hi I am working on nRF 52832 and nrf 52840 dongle. I want UART service to be used in my application and application should allow me to scan peripheral devices with user command...
I am a freshman. And I am doing some research on BTE by nRF52832(PCA10040). I want to get RSSI. Could you please tell me if there is a reference code or project in SDK? Many...
It takes time for fs_event_handler to be called back after nrf_fstorage_erase is executed.
In SDK13.1.0, it didn't take much time, but in SDK15.3.0 currently being developed...
Is there a way to create a command that gets throughput information from a device in the ble_app_interactive example? I want to get the throughput of a peripheral device once...
I am developing an universal remote which can be controlled via Bluetooth. For that I need to decode an IR signal.
I am using TSOP decoder.
The steps I think, I should...
Hello, we have made cars that play laser tag against eachother using infrared emitters and receivers. The problem is that the infrared radiation bounces off the surroundings...
Hello i have a rigado BMD-300 module and i would like to flash a new version of softdevice app and bootloader but i want to protect the UICR memory because that is where the...
Hi my goal is to put the NRF into system on low power mode every other second. I have a repeated app_timer that increments counter variable m_custom_value every second. I...
Hi,
I am developing a project using the nRF52840 DONGLE. As part of the process, I need to be able to debug my code, so I am using IAR and a J-TRACE PRO for that. The...
I am using NSDK 15.3, MeshSDK 3.2.0, SoftDevice 6.1.1 and nRF52840 DKs.
I successfully integrated the DFU capabilities in my firmware that uses BT Mesh. I am downloading...
I'm studying nRF52811 manual, there are moments not clear to me:
1. Is I/Q sampling paused during SWITCHING slots? For example, if I configure 16 1-msec slots (8 switching...
