Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi Support team,
My search for nrf8001 port to Arm-m3 landed me on a thread , where the support personnel has provided a link for a port to lpc1769 in the last comment....
Hi,
I would like to add sensor data in mesh network to be able to send data in certain intervals. How is it possible when I create a sensor model for mesh client and server...
Hello. I have a nRF52832 DK and I'm trying to modify the SPI example code found here:
/nRF5_SDK_15.0.0/nRF5_SDK_15.0.0_a53641a/examples/peripheral/spi
I'm using the nRF52832...
Hello Guys,
I have brought this nrf52840 to try BLE mesh. I tried connecting it to the PC and it was working fine, later I tried dumping the file into the board through...
Hey Nordic and co-nordic developpers,
Just to show some capabilities here at work I want to compile and run the mesh demo on the 10 Thingy52's we have here. I am currently...
Hi Nordic,
Could you please help me ! This is an urgent matter!
Based on this discussion , there is an error rate of actual baudrate comparing with the desired one.
...
Hello everyone,
I'm trying to use the new SDK 15.0.0 and the S140 soft device V6.0.0. I would like to use the LE CODED physical layer and set my TX output power, but when...
Why did the softdevice handler's API change?
sorry for a general question. I used SDK 13. and Now, I am porting my software to SDK 15. So, I have simple question. Why did...
My application is based of the UART example, I have a repeating app timer that fires every 5 min's to do some tasks, I also utilise single fire timers (initiated for events...
Ok, so I am using nRF52DK and trying to figure out to how to send up to 6 packets of data from custom service that sends 6 16bit values per packet. When I send one packet...
Hello,
We have a custom boards that powers a NRF52840 module from a 1.8v voltage regulator coming from a 3.6v battery. We also connected the positive pole of the battery...
I am new to embedded development. How do i physically connect the sensor to the board?
Is it possible without any additional equipment? What is important regarding pins...
Hi,
We want to certify a product embedded nRF51822 chip, with BAS and IAS defined by Bluetooth SIG.
Requesting SIG certification for it of a certification body, we were...
Hi all,
getting burnt out from searching the fourms and finding dead ends or outdated answers so just posting a question quickly.
Somewhere along the line my nrf51DK has...
I am working on a product based on the nRF52832 (using the Rigado BMD-300 module) which is basically a data logger with a BLE connection for offload. I am running FreeRTOS...
